Arctic Cat 1000 XT 2014 Скачать руководство пользователя страница 92

Страница: 92 / 151

GZ381A

5. Remove the throttle arm cover and disconnect the

throttle cable; then remove the throttle body from the

ATV.

GZ383A

6. Use tape to cover and seal the intake opening.

INSTALLING

1. Connect the throttle cable to the throttle body; then

remove the tape from the intake manifold and install
the throttle body using a new O-ring. Tighten the cap
screws securely.

GZ381A

2. Connect the three wiring connectors to the sensors;

then install the air filter housing and connect all
hoses. Tighten all clamps securely.

GZ094B

GZ091A

3. Connect the wiring connector to the IAT sensor.

4. Install the front rack and body panel (see Steer-

ing/Frame/Controls).

5. Install the seat making sure it locks securely in place.

Throttle Cable Free-Play

To adjust the throttle cable free-play, follow this proce-
dure.

1. Slide the rubber boot away; then loosen the jam nut

from the throttle cable adjuster.

CF297A

2. Turn the adjuster until the throttle cable has proper

free-play of 3-6 mm (1/8-1/4 in.) at the lever.

3. Tighten the jam nut against the throttle cable adjuster

securely; then slide the rubber boot over the adjuster.

CAUTION

Any objects or liquid entering the intake opening will
fall into the engine causing severe damage if the engine
is turned over or started.

Содержание 1000 XT 2014
























































































































































Результаты поиска

Содержание 1000 XT 2014

Отзывы:

Похожие инструкции для 1000 XT 2014

Бренды по названию

Популярные бренды

Arctic Cat 1000 XT 2014, Руководство по обслуживанию

Результаты поиска

Содержание 1000 XT 2014

Отзывы:

Похожие инструкции для 1000 XT 2014

Бренды по названию

Популярные бренды