Arctic Cat 1000 XT 2014 Скачать руководство пользователя страница 80

Страница: 80 / 151

GZ356

GZ363

3. With the outer rotor reference dot directed toward the

oil pump cover, install the rotor onto the inner rotor.

GZ360

4. Place a new O-ring seal on the outside of the oil pump

cover. The oil pump assembly is now ready for assem-
bly into the crankcase.

GZ362

CRANKSHAFT ASSEMBLY



NOTE: The crankshaft and connecting rod is a

non-serviceable assembly. If any component is out of
specification, the assembly must be replaced.

Measuring Connecting Rod
(Small End Inside Diameter)

1. Insert a snap gauge into the upper connecting rod

small end bore; then remove the gauge and measure it
with micrometer.

CC290D

2. Maximum diameter must not exceed specifications.

Measuring Connecting Rod
(Small End Deflection)

1. Place the crankshaft on a set of V blocks and mount a

dial indicator and base on the surface plate. Position
the indicator contact point against the center of the
connecting rod small end journal.

2. Zero the indicator and push the small end of the con-

necting rod away from the dial indicator.

3. Maximum deflection must not exceed specifications.

Measuring Connecting Rod
(Big End Side-to-Side)

1. Push the lower end of the connecting rod to one side

of the crankshaft journal.

2. Using a feeler gauge, measure the gap between the

connecting rod and crankshaft journal.

3. Acceptable gap range must be within specifications.

Measuring Crankshaft (Runout)

1. Place the crankshaft on a set of V blocks.

2. Mount a dial indicator and base on the surface plate.

Position the indicator contact at point 1 of the crank-
shaft.

Содержание 1000 XT 2014
























































































































































Результаты поиска

Содержание 1000 XT 2014

Отзывы:

Похожие инструкции для 1000 XT 2014

Бренды по названию

Популярные бренды

Arctic Cat 1000 XT 2014, Руководство по обслуживанию

Результаты поиска

Содержание 1000 XT 2014

Отзывы:

Похожие инструкции для 1000 XT 2014

Бренды по названию

Популярные бренды