APS 6RL Series, Руководство по эксплуатации

Страница: 138 / 204

6RL SERIES OPERATION MANUAL
SECTION 7: REMOTE PROGRAMMING
Entire Contents Copyright

2018 by Adaptive Power Systems, Inc. (APS) • All Rights Reserved • No reproduction without written authorization from APS.
6RL Series Regenerative DC Load Operation Manual Page 138 of 204
Configuration (before start)
Nr. Command Description
1 00 05 01 92 FF 00 2D FA Activate remote control
2 00 06 2E E1 00 03 91 04 Activate PV simulation mode DAYET
3 00 06 2E F0 00 00 81 00 Select technology: Manual (all required parameters must be
defined, here as with commands 4-10)
4 00 10 2F 02 00 02 04 3F 4C CC CD F7 ED
Fill factor voltage (FFU): 0,8
5 00 10 2F 04 00 02 04 3F 47 AE 14 EE FF Fill factor current (FFI): 0,78
6 00 10 2F 06 00 02 04 39 9D 49 52 84 57 Temperature coefficient α for ISC: 0,0003 /°C
7 00 10 2F 08 00 02 04 BB 44 9B A6 A1 7F Temperature coefficient β for UOC: -0,003 /°C
8 00 10 2F 0A 00 02 04 3D 94 7A E1 00 75
Scaling factor CU for UOC: 0,0725
9 00 10 2F 0C 00 02 04 39 66 AF CD 7F D1 Scaling factor CR for UOC: 0,00022 m²/W
10 00 10 2F 0E 00 02 04 3B 4E 70 3B A7 CE Scaling factor CG for UOC: 0,00315 W/m²
11 00 05 2E F1 FF 00 D5 30 Select input mode: ULIK
12 00 06 2F 10 61 47 E8 A8 Set open circuit voltage: 38 V (=0x6147)
13 00 06 2F 11 08 6F 97 26 Set short-circuit current: 7 A
14 00 05 2E F2 FF 00 25 30 Activate data recording
15 00 05 2E E5 00 00 D4 C4 Deactivate interpolation of day trend data
Write day trend data (before the start)
Nr. Command Description
16 00 05 2E E6 FF 00 65 34 Select access mode: write
17 00 05 2E E7 FF 00 34 F4 Delete former data (should be executed every time
before loading new data)
18 00 10 2E EA 00 06 0C 00 00 00 01 44 44 66
66 00 00 01 F4 88 23
Write 1
st day trend data set:
Irradiation: 500 W/m²
Temperature: 20°C Dwell time: 500 ms
19 00 10 2E EA 00 06 0C 00 00 00 02 6D 3A
74 0D 00 00 05 DC E4 C3
Write 2
nd
day trend data set:
Irradiation: 800 W/m²
Temperature: 28°C Dwell time: 1500 ms
... Write further data sets, a total of 500
517 00 10 2E EA 00 06 0C 00 00 01 F4 A3 D6 7F FF
00 00 4E 20 34 AF Write 500. day trend data set:
Irradiation: 1200 W/m²
Temperature: 35°C Dwell time: 20000 ms
Control, also during simulation run
Nr. Command Description
518 00 05 2E E6 FF 00 65 34 Start simulation -> the simulation will stop automatically after
the time that results from the total of dwell times in all
written data sets