manualshive.com logo in svg

Analog Devices EZ-KIT Lite ADSP-BF506F, Справочник по аппаратуре

Аналоговые устройства EZ-KIT Lite ADSP-BF506F - компактный и мощный инструмент для разработки DSP приложений. Здесь вы можете бесплатно скачать руководство по аппаратной части ("Hardware Reference Manual") для этого устройства. Скачать руководство можно на manualshive.com.

Поделиться
Скачать
background image

ADSP-BF50x Blackfin Processor Hardware Reference

15-39

UART Port Controllers

UARTx_IER_SET and UARTx_IER_CLEAR Registers

The interrupt enable register is not implemented as a data register. Instead
it is controlled by the

UARTx_IER_SET

and

UARTx_IER_CLEAR

register pair.

Writing ones to

UARTx_IER_SET

enables interrupts, writing

UARTx_IER_

CLEAR

disables them. Reads from either register return the enabled bits.

This way, different interrupt service routines can control transmit, receive,
and status interrupts independently and gracefully.

The

UARTx_IER

registers, shown in

Figure 15-14

and

Figure 15-15

, are

used to enable requests for system handling of empty or full states of
UART data registers. Unless polling is used as a means of action, the

ERBFI

and/or

ETBEI

bits in this register are normally set.

Setting this register without enabling system DMA causes the UART to
notify the processor of data inventory state by means of interrupts. For
proper operation in this mode, system interrupts must be enabled, and
appropriate interrupt handling routines must be present.

Each UART features three separate interrupt channels to handle
data transmit, data receive, and line status events independently,
regardless whether DMA is enabled or not. If no DMA channels
are assigned to the UART, set the

EGLSI

bit in the

UARTx_GCTL

register to reroute transmit and receive interrupts to the status
interrupt output.

With system DMA enabled, the UART uses DMA to transfer data to or
from the processor. Dedicated DMA channels are available to receive and
transmit operation. Line error handling can be configured completely
independently from the receive/transmit setup.

Table 15-10. UART Receive Buffer Register Memory-Mapped Addresses

Register Name

Memory-Mapped Address

UART0_RBR

0xFFC0 042C

UART1_RBR

0xFFC0 202C

Содержание EZ-KIT Lite ADSP-BF506F































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для EZ-KIT Lite ADSP-BF506F

AXIOMTEK CAPA313 Quick Installation Manual preview
CAPA313
Бренд: AXIOMTEK Страницы: 2
Linear Technology DC708 Quick Start Manual preview
DC708
Бренд: Linear Technology Страницы: 6
MSI MS-6367 Manual preview
MS-6367
Бренд: MSI Страницы: 30
Linear Technology DC2461A Manual preview
DC2461A
Бренд: Linear Technology Страницы: 7
Biostar 915GV-M7 Manual preview
915GV-M7
Бренд: Biostar Страницы: 65
Ublox SARA-N3 series User Manual preview
SARA-N3 series
Бренд: Ublox Страницы: 18
M-system DiskOnChip PCI-G-EVB User Manual preview
DiskOnChip PCI-G-EVB
Бренд: M-system Страницы: 14
FIC FR33E Manual preview
FR33E
Бренд: FIC Страницы: 52
Intel DH67CF Product Manual preview
DH67CF
Бренд: Intel Страницы: 76
OMS AS7421 Quick Start Manual preview
AS7421
Бренд: OMS Страницы: 11
ASROCK K10N750SLI-WIFI User Manual preview
K10N750SLI-WIFI
Бренд: ASROCK Страницы: 264
CAME ZBX4 Electrical Connections preview
ZBX4
Бренд: CAME Страницы: 4
Texas Instruments TLV320AIC12KEVM-K User Manual preview
TLV320AIC12KEVM-K
Бренд: Texas Instruments Страницы: 40
ASROCK H61M-HVGS User Manual preview
H61M-HVGS
Бренд: ASROCK Страницы: 162
u-blox EVK-M8QCAM User Manual preview
EVK-M8QCAM
Бренд: u-blox Страницы: 24
DFI P4X533-ALE User Manual preview
P4X533-ALE
Бренд: DFI Страницы: 113
Analog Devices EVAL-AD5344DBZ User Manual preview
EVAL-AD5344DBZ
Бренд: Analog Devices Страницы: 12
Analog Devices EVAL-AD5161DBZ User Manual preview
EVAL-AD5161DBZ
Бренд: Analog Devices Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды