manualshive.com logo in svg

Analog Devices EZ-KIT Lite ADSP-BF506F, Справочник по аппаратуре, Страница: 314 / 1310

Поделиться
Скачать
Analog Devices EZ-KIT Lite ADSP-BF506F Скачать руководство пользователя страница 314

DMA Registers

7-78

ADSP-BF50x Blackfin Processor Hardware Reference

DMA Inner Loop Address Increment Registers 

(DMAx_X_MODIFY/MDMA_yy_X_MODIFY)

The

DMAx_X_MODIFY

register, shown in

Figure 7-12

, contains a signed,

two’s-complement byte-address increment. In 1-D DMA, this increment
is the stride that is applied after transferring each element.

DMAx_X_MODIFY

is specified in bytes, regardless of the DMA transfer

size.

In 2-D DMA, this increment is applied after transferring each element in
the inner loop, up to but not including the last element in each inner
loop. After the last element in each inner loop, the

DMAx_Y_MODIFY

register

is applied instead, except on the very last transfer of each work unit. The

DMAx_X_MODIFY

register is always applied to the last transfer of a work unit.

The

DMAx_X_MODIFY

field may be set to 0. In this case, DMA is performed

repeatedly to or from the same address. This is useful, for example, in
transferring data between a data register and an external memory-mapped
peripheral.

Figure 7-11. DMA Current Inner Loop Count Registers

15 14

13 12

11 10

9

8

7

6

5

4

3

2

1

0

X

CURR_X_COUNT[15:0]
(Current Inner Loop
Count)

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

DMA Current Inner Loop Count Registers (DMAx_CURR_X_COUNT/

MDMA_yy_CURR_X_COUNT)

R/W prior to enabling channel; RO after enabling channel

Reset = Undefined

Loaded by X_COUNT
at the beginning of each
DMA session (1-D DMA),
or at the beginning of
each row (2-D DMA)

Содержание EZ-KIT Lite ADSP-BF506F































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов