manualshive.com logo in svg

Analog Devices EZ-KIT Lite ADSP-BF506F, Справочник по аппаратуре

Аналоговые устройства EZ-KIT Lite ADSP-BF506F - компактный и мощный инструмент для разработки DSP приложений. Здесь вы можете бесплатно скачать руководство по аппаратной части ("Hardware Reference Manual") для этого устройства. Скачать руководство можно на manualshive.com.

Поделиться
Скачать
background image

ADSP-BF50x Blackfin Processor Hardware Reference

7-5

Direct Memory Access

The 16-bit DMA core bus (DCB) connects the DMA controller to a dedi-
cated port of L1 memory. L1 memory has dedicated DMA ports featuring
special DMA buffers to decouple DMA operation. See

Blackfin Processor

Programming Reference

for a description of the L1 memory architecture.

The DCB bus operates at core clock (

CCLK

) frequency. It is the DMA con-

troller’s responsibility to translate DCB transfers to the system clock
(

SCLK

) domain.

The 16-bit DMA access bus (DAB) connects the DMA controller to the
on-chip peripherals. This bus operates at

SCLK

frequency.

The 16-bit DMA external bus (DEB) connects the DMA controller to the
EBIU port. This bus is used for all peripheral and memory DMA transfers
to and from external memories and devices. It operates at

SCLK

frequency.

Transferred data can be 8-, 16-, or 32-bits wide. The DMA controller,
however, connects only to 16-bit buses.

Memory DMA can pass data every SCLK cycle between L1 memory and
the EBIU. Transfers from L1 memory to L1 memory require two cycles, as
the DCB bus is used for both source and destination transfers. Similarly,
transfers between two off-chip devices require EBIU and DEB resources
twice. Peripheral DMA transfers can be performed every other SCLK
cycle.

For more details on DMA performance see

“DMA Performance” on

page 7-41

.

Peripheral DMA

The DMA controller features 12 channels that perform transfers between
peripherals and on-chip or off-chip memories. The user has full control
over the mapping of DMA channels and peripherals. The default DMA
channel priority and mapping, shown in

Table 7-7 on page 7-105

, can be

changed by altering the 4-bit

PMAP

field in the

DMAx_PERIPHERAL_MAP

regis-

ters for the peripheral DMA channels.

Содержание EZ-KIT Lite ADSP-BF506F































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для EZ-KIT Lite ADSP-BF506F

Xilinx FMC XM101 LVDS QSE User Manual preview
FMC XM101 LVDS QSE
Бренд: Xilinx Страницы: 23
MYiR MYC-C8MMQ6-8E2D-160-I Linux Development Manual preview
MYC-C8MMQ6-8E2D-160-I
Бренд: MYiR Страницы: 50
Zotac 890GX series User Manual preview
890GX series
Бренд: Zotac Страницы: 54
Freetech P8F155 User Manual preview
P8F155
Бренд: Freetech Страницы: 79
Avalue Technology EMX-ZXEDP User Manual preview
EMX-ZXEDP
Бренд: Avalue Technology Страницы: 80
TDK SmartSound One User Manual preview
SmartSound One
Бренд: TDK Страницы: 11
JETWAY S446R2A User Manual preview
S446R2A
Бренд: JETWAY Страницы: 54
Avalue Technology SEAX-H81 User Manual preview
SEAX-H81
Бренд: Avalue Technology Страницы: 60
Icop VDX-6328RD-NF User Manual preview
VDX-6328RD-NF
Бренд: Icop Страницы: 41
MSI A320M gaming pro Manual preview
A320M gaming pro
Бренд: MSI Страницы: 20
Supero X7SBL-LN1 User Manual preview
X7SBL-LN1
Бренд: Supero Страницы: 95
Supero X7DVL-3 User Manual preview
X7DVL-3
Бренд: Supero Страницы: 108
Supero Supero X8SIT-F User Manual preview
Supero X8SIT-F
Бренд: Supero Страницы: 99
Supero Supero X8DTU-6F+ User Manual preview
Supero X8DTU-6F+
Бренд: Supero Страницы: 111
Supero Supero X7SBL-LN1/LN2 User Manual preview
Supero X7SBL-LN1/LN2
Бренд: Supero Страницы: 95
Supero Super X8DAH+ User Manual preview
Super X8DAH+
Бренд: Supero Страницы: 101
Supero SUPER P6DLE User Manual preview
SUPER P6DLE
Бренд: Supero Страницы: 66
Supero SUPER P3TDLR User Manual preview
SUPER P3TDLR
Бренд: Supero Страницы: 90

Бренды по названию

Популярные бренды

Загрузить еще бренды