manualshive.com logo in svg

Analog Devices EZ-KIT Lite ADSP-BF506F, Справочник по аппаратуре, Страница: 599 / 1310

Поделиться
Скачать
Analog Devices EZ-KIT Lite ADSP-BF506F Скачать руководство пользователя страница 599

ADSP-BF50x Blackfin Processor Hardware Reference

15-5

UART Port Controllers

Internal Interface

The UARTs are DMA-capable peripherals with support for separate TX
and RX DMA master channels. They can be used in either DMA or pro-
grammed non-DMA mode of operation. The non-DMA mode requires
software management of the data flow using either interrupts or polling.
The DMA method requires minimal software intervention as the DMA
engine itself moves the data. For more information on DMA, see the

Direct Memory Access

chapter.

All UART registers are 8 bits wide. They connect to the PAB bus. The

UARTx_RBR

and

UARTx_THR

registers also connect to one of the DABx bus-

ses. While UART0 and UART1 connect to the DAB16 bus.

Each UART has three interrupt outputs. The transmit request and receive
request outputs can function as DMA requests and connect to the DMA
controller. Therefore, if the DMA is not enabled, the DMA controller
simply forwards the request to the SIC controller. The status interrupt
output connects directly to the SIC controller.

When no DMA channel is assigned, a UART has only one inter-
rupt output. To modify, set the

EGLSI

bit in the

UARTx_GCTL

register to redirect transmit and receive requests to the status inter-
rupt output.

Every UART’s RX pin is also sensed by the alternative capture input
(

TACIx

) of one of the general-purpose timers.

Table 15-1

shows the assign-

ment. In capture mode, the timers can be used to detect the bit rate of the
received signal. See

“Autobaud Detection” on page 15-20

.

Description of Operation

The sections that follow describe the operation of the UART.

Содержание EZ-KIT Lite ADSP-BF506F































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов