AMX Epica DGX 32 Скачать руководство пользователя | Manualshive

Страница: 52 / 147

background image

Epica DGX 32 SC Optical Boards

46

Epica DGX 32 Instruction Manual

Specifications Epica DGX 32 SC Optical Boards

Applies to input board FG1056-500 and output board FG1056-510.

Compatible AMX AutoPatch DGX Fiber modules:

FG1010-200-01 – AVB-TX-DGX-HD15-SC Fiber

FG1010-210-01 – AVB-TX-DGX-DVI-SC Fiber

FG1010-400-01 – AVB-RX-DGX-SC Fiber-HD15

FG1010-410-01 – AVB-RX-DGX-SC Fiber-DVI

Note: Either Transmitter (TX) module can be used in conjunction with either Receiver (RX) module.

* 96 kHz audio is only available when the source video resolution is 800x600 @ 60 Hz (40 MHz pixel clock) or
greater. Otherwise 48 kHz is the maximum.

** 3000 ft. cable requires 50/125

μ

m OM2 class low loss fiber cable.

***480i and 576i are only available when being transmitted from a DGX HD-15 TX as a Y-Pb-Pr signal.

Important: These boards are compatible only with other AMX AutoPatch products that support
the DGX single fiber technology. They are not compatible with third-party optical distribution
amplifiers or multimode to single-mode converters.

AMX reserves the right to modify its products and their specifications without notice.

Epica DGX 32 SC Optical

Specifications

Parameter

Value

Compatible AMX AutoPatch Fiber Products DGX HD-15 TX and RX, DGX DVI TX and RX,

other AMX AutoPatch DGX SC Fiber signal management
products

Signal Types over Fiber

Video, audio, serial data
Video signal must be present to pass audio and serial data

Resolution Support

640x480 @ 60 Hz up to 1920x1200 @ 60 Hz

Interlaced Resolution Support

1080i 60, 59.94, 50 (fields per second)
576i 100, 50 (fields per second)***
480i 60 (fields per second)***

Audio Support

Analog stereo or S/PDIF (S/PDIF up to 96 kHz sample rate*)

Serial Data Support

Unidirectional RS-232, up to 115.2 k baud

Fiber Cable Type

Multimode Simplex (with SC termination)
50/125

μ

m (preferred) or 62.5/125

μ

m

Fiber Cable Length

Up to 3000 ft. (914.4 m) in with 50

μ

m cable**

Up to 3000 ft. (914.4 m) out with 50

μ

m cable**

Up to 1500 ft. (457.2 m) in with 62.5

μ

m cable

Up to 1500 ft. (457.2 m) out with 62.5

μ

m cable

Optical Budget

9.75 dBm (typical) between DGX TX and input board
9.75 dBm (typical) between output board and DGX RX
Optical Modulation Amplitude (OMA) Output: -6.25 dBm (typical)
Optical Modulation Amplitude (OMA) Input Sensitivity: -16.0 dBm
(typical)

Power Output of Laser Radiation (max.)

4.08 mW (DGX 32 SC Optical Output Board)

Safety Certifications

Class 1 Laser Product (Class 3R Laser Product when fiber is
disconnected from the unit) IEC 60825-1, 2001
(DGX 32 SC Optical Output Board)

Fiber Connector

SC optical

«
...
50
51
52
53
54
...
»

Содержание Epica DGX 32




















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Epica DGX 32

TotalStorage 3534-F08

Бренд: IBM Страницы: 105

RedBooks SAN24B-5

Бренд: IBM Страницы: 11

RedBooks SAN24B-5

Бренд: IBM Страницы: 2

Бренд: IBM Страницы: 123

8265 Nways ATM Switch

Бренд: IBM Страницы: 192

Бренд: IOGear Страницы: 1

Бренд: Steren Страницы: 13

Бренд: Eaton Страницы: 5

Бренд: Intel Страницы: 162

Бренд: ALFAtron Страницы: 15

Бренд: ABM Страницы: 8

Бренд: T.I.P. Страницы: 42

Бренд: Digitus Страницы: 10

Бренд: Kathrein Страницы: 41

Бренд: N-Tron Страницы: 2

Бренд: Xantech Страницы: 32

Бренд: LevelOne Страницы: 6

Бренд: Novy Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды