AMX Epica DGX 32 Скачать руководство пользователя

Страница: 58 / 147

Epica DGX 32 DVI Boards

Epica DGX 32 Instruction Manual

Specifications Epica DGX 32 DVI

Applies to input board FG1056-520 and output board FG1056-530.

EDID Resolutions Supported through Local DDC

Standard Timings

* This is the preferred timing identified in the EDID.

Established Timings

** Some monitors may not support the maximum refresh rate.

AMX reserves the right to modify its products and their specifications without notice.

Digital Video – DVI

Specifications

Parameter

Value

Signal Type

DVI-D (single link)

Resolution Support

640x480 @ 60 Hz up to 1920x1200 @ 60 Hz

Interlaced Resolution Support

1080i 60, 59.94, 50 (fields per second)
576i 100, 50 (fields per second)
480i 60 (fields per second)

Data Rate (max.)

4.95 Gbps

Pixel Clock (max.)

165 MHz

DDC/EDID Support

EDID provided by Epica DGX 32
EDID is user re-programmable

HDCP Support

Input Voltage (nominal)

1.0 Vpp differential

Input Cable Equalization

Up to 50 ft. (15.24 m)

Output Nominal Voltage

1.0 Vpp differential

Output Reclocking

Yes

5 V DDC Pin

250 mA

Output Rise Time / Fall Time

80 ps min. to 200 ps max. (20% to 80%)
0.13 UI min. to 0.33 UI max. (@ 1.65 Gbps, 20% to 80%)

Connector

DVI-I (DVI-D single link is the supported signal type)

Standard Timing

Identification

Resolutions

Refresh Rate Max.**

ID 1

1920x1200*

60 Hz

ID 2

1920x1080

60 Hz

ID 3

1680x1050

60 Hz

ID 4

1600x1200

60 Hz

ID 5

1280x800

60 Hz

ID 6

1280x720

60 Hz

ID 7

1280x1024

60 Hz

ID 8

640x480

120 Hz

Resolutions

Refresh Rate Max.**

640x480

60 Hz, 72 Hz, 75 Hz

800x600

56 Hz, 60 Hz, 72 Hz, 75 Hz

1024x768

60 Hz, 70 Hz, 75 Hz, 87 Hz

1280x1024

75 Hz

Содержание Epica DGX 32




















































































































































Результаты поиска

Содержание Epica DGX 32

Отзывы:

Похожие инструкции для Epica DGX 32

Бренды по названию

Популярные бренды

AMX Epica DGX 32, Инструкция по эксплуатации

Результаты поиска

Содержание Epica DGX 32

Отзывы:

Похожие инструкции для Epica DGX 32

Бренды по названию

Популярные бренды