AMX Epica DGX 32 Скачать руководство пользователя | Manualshive

Страница: 10 / 147

background image

Notices

4

Epica DGX 32 Instruction Manual

Notices

Copyright Notice

AMX

©

2010 (Rev A), all rights reserved. No part of this publication may be reproduced, stored in a

retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying,
recording, or otherwise, without the prior written permission of AMX. Copyright protection claimed
extends to AMX hardware and software and includes all forms and matters copyrightable material and
information now allowed by statutory or judicial law or herein after granted, including without
limitation, material generated from the software programs which are displayed on the screen such as
icons, screen display looks, etc. Reproduction or disassembly of embodied computer programs or
algorithms is expressly prohibited.

Liability Notice

No patent liability is assumed with respect to the use of information contained herein.

While every precaution has been taken in the preparation of this publication, AMX assumes no
responsibility for error or omissions. No liability is assumed for damages resulting from the use of the
information contained herein.

Further, this publication and features described herein are subject to change without notice.

Trademark Notices

AMX

®

, AutoPatch

®

, NetLinx

®

, and SmartScale

™

are trademarks of AMX.

Windows

®

, Windows 2000

®

, Windows NT

®

, and Windows XP Professional

®

are registered trademarks

of Microsoft Corporation.

HyperTerminal

®

is a copyright product of Hilgraeve Inc.

3M

®

, Desco

®

, Richmond Technology

®

, and Plastic Systems

®

are registered trademarks.

Neuron

®

and LonTalk

®

are registered trademarks of Echelon.

TosLink

®

is a registered trademark of the Toshiba Corporation.

Ethernet

®

is a registered trademark of the Xerox Corporation.

ENERGY STAR

®

is a registered trademark of the U.S. Department of Energy and the

U.S. Environmental Protection Agency.

Other products mentioned herein may be the trademarks of their respective owners.

Lithium Batteries Notice

Switzerland requires the following notice for products equipped with lithium batteries. This notice is not
applicable for all AMX equipment.

Upon shipment of products to Switzerland, the requirements of the most up-to-date Swiss Ordinance
Annex 2.15 of SR 814.81 will be met including provision of the necessary markings, documents, and
annual reports relative to the disposal of the batteries to the Swiss Authorities.

«
...
8
9
10
11
12
...
»

Содержание Epica DGX 32




















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Epica DGX 32

Бренд: Hama Страницы: 10

Бренд: Hama Страницы: 14

Бренд: 3Com Страницы: 12

S7906E - Switch

Бренд: 3Com Страницы: 8

Бренд: Broadcast Tools Страницы: 28

Бренд: Teseq Страницы: 60

Бренд: Contemporary Controls Страницы: 4

Premasreg 716 Series

Бренд: S+S Regeltechnik Страницы: 32

PerfectView GPS300

Бренд: Waeco Страницы: 72

Бренд: Manhattan Страницы: 4

SICOM3432G Series

Бренд: KYLAND Страницы: 29

Бренд: Microsonic Страницы: 2

Бренд: MTHTrains Страницы: 16

Бренд: Cross Technologies Страницы: 11

SMT-8-...-B Series

Бренд: Festo Страницы: 2

Бренд: Kramer Страницы: 10

Бренд: Southern States Страницы: 32

Бренд: Zamel Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды