Appendix A – EDID Programmer
105
Epica DGX 32 Instruction Manual
Reading and Saving EDID Data from a Destination Device
Tip: The Save button in the EDID Programmer can be used to save the EDID information as an
.edid file, which can be opened as a text file (click on the Open button) and edited or opened and
written to an input (click the Write button).
The instructions below cover the situation in which the EDID Programmer is used to read the EDID
information from a destination device in the installation with a DVI connector (an HD-15 connector can
also be used). Additional information for using cable adapters is provided on the next page.
To read and save EDID data from a destination device:
1.
On the PC, open the EDID Programmer.
2.
Connect a DVI cable to the PC using the PC’s spare monitor port (if your laptop has an HD-15
[VGA] port, see “Using Cable Adapters” on the next page).
3.
Connect the open end of the DVI video cable to the destination device (typically a monitor) from
which the EDID information needs to be read.
4.
Click the Refresh Display List button to update the Available Displays drop down list.
5.
From the Available Displays drop down list, select the destination device from which you need to
read the EDID.
6.
Click the Read button to read the EDID information. The results display in the read-only area.
7.
Click the Save button (select location, enter file name, and click Save).
Leave the EDID Programmer open for instructions on writing the EDID to the TX on the next page.
8.
Disconnect the DVI cable from the PC and from the destination device.
FIG. 46
EDID Programmer
Available Displays drop down list – select device
Close – shuts down application; will not prompt to save
Open – an EDID file
Save – an EDID file to edit or to write to input on board
Refresh Display List – updates list after additional devices attached
Convert to Digital / Convert to Analog – converts displayed EDID data
Query AutoPatch Device – acquires enclosure’s XNNet ID address
EDID Information – data (read-only) from file or device
EDID Type – indicates digital or analog (read-only)
Read – reads EDID from selected destination device
Write – writes EDID to input on board
Communication menu – use to select PC serial port or change baud rate
Status – shows application status (read-only)
Target Device – select Matrix Switcher
Содержание Epica DGX 32
