AMX Epica DGX 32 Скачать руководство пользователя | Manualshive

Страница: 84 / 147

background image

NXB-AP-1000 Interface – Initial Setup by Network Admin

78

Epica DGX 32 Instruction Manual

System Requirements

Web browser (Internet Explorer, Firefox, Netscape, etc.)

JRE v1.4.x or greater (Java Plug-in for the XBar Controller)

Design Requirement

AMX highly recommends deploying only one NXB-AP-1000 Interface per system. Any configuration
violating this recommendation may not be backed by the technical support agreement. The
NXB-AP-1000 Interface offers a single, remote access point to a system, and its interactions with that
system can cause interference and collision issues if more than one NXB-AP-1000 Interface is present.

Note: The instructions in this chapter assume that all of the AMX AutoPatch devices in the system
are connected and powered up.

Opening the NXB-AP-1000 Interface

Caution: We strongly recommend that the NXB-AP-1000 Interface site be placed inside your
network firewall and that system security be turned on.

A worksheet to record connection information is provided at the end of this chapter (see page 91).

To set up the NXB-AP-1000 Interface:

1.

Follow the directions on page 40

for connecting the TCP/IP connector on the Epica DGX 32

enclosure’s CPU to a LAN or to a network card in a PC.

2.

Launch a browser on your PC.

3.

Type the IP address (as determined on page 80) in the address bar of the browser and press Enter.
The PC must be on the same subnet (e.g., 192.168.X.X).
The NXB-AP-1000 Interface Home page opens. The Home page contains system configuration
information.

4.

Complete any necessary configuration of the

NXB-AP-1000 Interface. Instructions are included in

this chapter.

If the Home page does not open, see the “NXB-AP-1000 Troubleshooting” section on page 43.

«
...
82
83
84
85
86
...
»

Содержание Epica DGX 32




















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Epica DGX 32

Бренд: Gefen Страницы: 11

xStack DES-3500 Series

Бренд: D-Link Страницы: 260

DXS-3600 Series

Бренд: D-Link Страницы: 48

DXS-3400 SERIES

Бренд: D-Link Страницы: 3

Web Smart Switch DGS-1210-16

Бренд: D-Link Страницы: 71

Бренд: D-Link Страницы: 3

Бренд: D-Link Страницы: 56

xStack DES-3800 Series

Бренд: D-Link Страницы: 326

xStack DES-3526

Бренд: D-Link Страницы: 222

Бренд: D-Link Страницы: 2

DXS-1210 Series

Бренд: D-Link Страницы: 20

SmartSwitch 9A100

Бренд: Cabletron Systems Страницы: 52

SmartSwitch 9W006

Бренд: Cabletron Systems Страницы: 34

SmartSTACK ELS100-S24TX2M

Бренд: Cabletron Systems Страницы: 102

Бренд: Cabletron Systems Страницы: 24

SmartSwitch 9000

Бренд: Cabletron Systems Страницы: 14

Бренд: Cabletron Systems Страницы: 38

Бренд: Pathway connectivity solutions Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды