manualshive.com logo in svg

Ametek Sorensen SG Series, Руководство по программированию, Страница: 79 / 149

Поделиться
Скачать
Ametek Sorensen SG Series Скачать руководство пользователя страница 79

SG Series Programming 

SCPI Command Operation 

M550129-03 Rev L

 

6-13

 

 

 

 

[:AMPLitude] <NRf> 

 

 

 

[:AMPLitude?] 

 

 

:PROTection 

 

 

:PROTection? 

 

 

 

[:LEVel] <NRf> 

 

 

 

[:LEVel?] 

 

 

 

:TRIPped? 
:STATe? 
:CLEar 

 

 

:RAMP <NRf> <NRf> 

 

 

:RAMP? 

 

 

 

:ABORt 

 

 

 

:ALL? 

 

 

 

:HTRIGgered <NRf> <NRf> 

 

 

 

:HTRIGgered? 

 

 

 

:TRIGgered <NRf> <NRf> 

 

 

 

:TRIGgered?

 

 

 

:TRIGgered  

 

 

:TRIGgered?  

 

 

 

:CLEar 

 

 

 

:AMPLitude <NRf> 
:AMPLitude?

 

6.5.2

 

SOURCE SCPI Command Reference 

The lett

er “C” in the “SCPI” column means that the command syntax is 

SCPI compliant; an “N” in the “SCPI” column means that the command 
syntax is not part of the SCPI definition. 

 

Command 

Description 

SCPI 

SOURce 

Source subsystem.  

C 

   :CURRent 

Sets the output current in amps (default) or in milliamps. 

C 

   :CURRent? 

Returns the output current in amps or in milliamps 

C 

      [:LEVel] 

Sets the output current in amps (default) or in milliamps. 

C 

      [:LEVel?] 

Returns the output current in amps or in milliamps. 

C 

         [:IMMediate] 

Sets the output current in amps (default) or in milliamps. 

C 

         [:IMMediate?] 

Returns the output current in amps or in milliamps 

C 

            [:AMPLitude] 
<NRf> 

Sets the output current in amps (default) or in milliamps. 

C 

            [:AMPLitude?] 

Returns the output current in amps or in milliamps 

C 

      :LIMit 

Sets an upper soft limit on the programmed output current 
for the supply.  The soft limit prevents the supply from being 
inadvertently programmed above the soft limit, thus 
providing a method for protecting the load against 
damaging currents. 

C 

      :LIMit? 

Returns the upper soft limit on the programmed output 
current for the supply. 

C 

         [:AMPLitude] 
<NRf> 

Sets an upper soft limit on the programmed output current for 
the supply. 

C 

         [:AMPLitude?] 

Returns the upper soft limit on the programmed output 
current for the supply. 

C 

Содержание Sorensen SG Series






















































































































































Отзывы:

Нет отзывов