Amada RG35S-100 Скачать руководство пользователя страница 97 | Manualshive

Страница: 97 / 110

Amada RG35S-100 Скачать руководство пользователя страница 97

VI-5

2-2. Changing hydraulic oil

Change the hydraulic oil after about first three months of machine
operation and every year or 2000 hours of machine operation thereafter.
(The hydraulic oil should be changed entirely even if it was added in the
midway.)

Model

Tank capacity

RG35S

26 L {6.9 US gal}

RG50, RG80

51 L {13.5 US gal}

RG100

65 L {17.2 US gal}

Recommended hydraulic oil: Amada Oil A-110

Esso Nuto H46
Mobil DTE 25
Shell Tellus Oil 46
(ISO VG46 equivalent)

NOTICE

O

When the hydraulic oil is changed, also clean the filters in the hydraulic oil
tank.

Change the hydraulic oil as described below.

1

Open the ram to the maximum opening limit.

2

Press the HYD. OFF button. The HYD. ON button extinguishes,

and the hydraulic pump motor stops.

3

Turn the POWER ON/OFF keyswitch to OFF.

4

Remove all bolts fixing the two top covers of the tank, and remove

the top covers. (For the RG35S remove the one top cover in the
same way.)

5

Drain the old hydraulic oil from the tank into an empty can, using a
pump.
If the pump is not available, prepare an empty can of such a
capacity as to match the tank capacity (refer to the table above),
and place it below the drain plug of the tank. Remove the drain
plug to drain the old hydraulic oil from the tank into the can.

6

Wipe the inside of the tank with a clean cloth.

7

Remove all filters from the tank.

8

Blow the dust off the inside of
the filters with an air gun.

9

Replace the filters in the tank.

FILTER

«
...
95
96
97
98
99
...
»

Содержание RG35S-100















































































































Отзывы:

Нет отзывов