manualshive.com logo in svg

Amada RG35S-100, Руководство оператора, Страница: 88 / 110

Поделиться
Скачать
Amada RG35S-100 Скачать руководство пользователя страница 88

V-44

11. TURNING OFF POWER

CAUTION

O

Whenever the machine is not in use,
remove the key from the POWER ON/OFF
keyswitch, and hand it to the chief
operator for custody.

O

When the ram is positioned above the
maximum opening limit, stopping the
hydraulic pump motor opens the ram even
if the bar pedal is locked.    Before
stopping the hydraulic pump motor,
unlock the bar pedal, and open the ram to
the maximum opening limit.

NOTICE

O

When stopping the machine at the end of the day’s work, turn off its power
with the ram positioned at the multiple opening limit.

Turn off the power of the machine as described below.

 

1

Turn up the multiple opening limit setting lever to clear the multiple
opening limit of the ram.
The ram opens to the maximum opening limits.

 

2

Press the HYD. OFF button.
The HYD. ON button
extinguishes, and the hydraulic
pump motor stops.

 

3

Turn the POWER ON/OFF
keyswitch to OFF, and remove
the key from the keyswitch.

Содержание RG35S-100















































































































Отзывы:

Нет отзывов