Amada RG35S-100 Скачать руководство пользователя страница 94

Страница: 94 / 110

VI-2

1. INSPECTION BEFORE START OF DAY'S

WORK

Inspection before the start of the day's work is very important for the
safe and trouble-free operation of the machine. Before starting the
operation of the machine, be sure to inspect the following items.

No.

Item

Method

Remedy

Primary power cable is not
damaged.

Visually check.

If cable is damaged, change
it immediately.

Switches, buttons, and
lamps are not functionally or
visually damaged.

Visually and tactually check. If switches and buttons

malfunction or are damaged,
and if lamps are burnt out,
contact AMADA for
changing them.

Hydraulic pump motor does
not produce abnormal noise.

Aurally check.

If abnormal noise is heard,
contact AMADA.

There are no hydraulic oil
leaks.

Visually check.

If there is hydraulic oil leak,
contact AMADA for repairing
it.

Ram normally operates.

Refer to “Checking ram for
operation” on next page.

If ram does not normally
operate, contact AMADA.

EMERGENCY STOP
buttons normally operate.

Remove tools from
machine.

Press bar pedal, and
press one of
EMERGENCY STOP
buttons while ram is
closing.

If ram does not stop when
EMERGENCY STOP button
is pressed, contact AMADA.

Tools are fixed in place.

Visually and tactually check. Correctly install tools. (For

detailed procedure, refer to
“5. Installing tools” in Part V.)

Tools are not damaged.

Visually check.

If tools are damaged,
change them.

Hydraulic oil level is proper.
(When ram is at maximum
opening limit, hydraulic oil
level is near middle mark of
oil gauge.)

Visually check.

If hydraulic oil level is low,
add hydraulic oil. (Refer to
“2-1. Checking hydraulic oil
level” in this Part.)

Pressure gauge is not
functionally or visually
damaged.

Visually check.

Ask AMADA to change
pressure gauge if pointer is
missing or does not move, or
if glass is broken.

Содержание RG35S-100















































































































Результаты поиска

Содержание RG35S-100

Отзывы:

Amada RG35S-100, Руководство оператора, Страница: 94 / 110

Результаты поиска

Содержание RG35S-100

Отзывы: