Amada RG35S-100 Скачать руководство пользователя страница 96 | Manualshive

Страница: 96 / 110

Amada RG35S-100 Скачать руководство пользователя страница 96

VI-4

2. MAINTAINING HYDRAULIC SYSTEM

If the hydraulic oil is badly contaminated, change it.

NOTICE

O

When dirt, dust, and other foreign matter are deposited in large amounts in
the hydraulic circuit, the hydraulic pump may produce abnormal noise and
decrease in discharge capacity, and the ram may decrease in bending speed
and vibrate. These conditions are attributable to the plugging of the filters in
the hydraulic oil tank. Remove the filters, and clean or change them.

2-1. Checking hydraulic oil level

Open the ram to the maximum opening limit, turn the POWER ON/OFF
keyswitch to OFF, and check that the hydraulic oil is filled to the middle
mark of the oil gauge.
If the hydraulic oil level is low, remove the top cover or covers of the
hydraulic oil tank, and add the hydraulic oil into the tank.

OIL GAUGE

TOP COVER

OIL GAUGE

[RG35S]

OIL GAUGE

OIL GAUGE

TOP COVERS

[RG50, RG80, RG100]

NOTICE

O

Be sure to add the same hydraulic oil as originally used.

O

Check that the hydraulic pressure indication is stable when pressure is
applied.

«
...
94
95
96
97
98
...
»

Содержание RG35S-100















































































































Отзывы:

Нет отзывов