manualshive.com logo in svg

Amada RG35S-100, Руководство оператора, Страница: 73 / 110

Поделиться
Скачать
Amada RG35S-100 Скачать руководство пользователя страница 73

V-29

Removing punches from rear clamping plates

WARNING

O

When loosening the rear fixing bolts, do
not turn them counterclockwise by more
than one and a half turns.    If the bolts are
turned by more than one and a half turns,
the rear fall prevention mechanism does
not operate, allowing the punch to fall in a
dangerous manner.

 

1

Turn the rear fixing
bolts
counterclockwise by
one turn with an Allen
wrench as shown
right.

  2

Remove the punch by
sliding it sideways.

REAR FIXING

BOLTS

TURN REAR FIXING BOLTS

COUNTERCLOCKWISE

7-2-3. INSTALLING AND REMOVING REAR CLAMPING PLATES

WARNING

O

Before installing and removing the rear
clamping plates, turn the POWER ON/OFF
keyswitch to OFF, remove the key from the
keyswitch, and keep it by yourself.

Before installing and removing the rear clamping plates, be sure to
remove the punch holder units from the upper beam.

Removing rear clamping plates

 

1

Place the punch
holder unit so that the
rear clamping plate
faces down as shown
right.

REAR CLAMPING 
PLATE

Содержание RG35S-100















































































































Отзывы:

Нет отзывов