Altigen ACC 6.7 Скачать руководство пользователя страница 381 | Manualshive

Страница: 381 / 462

background image

Chapter 28: Microsoft Exchange Integration

MAXCS ACC 6.7 Administration Manual 367

Figure 153. Choosing the

Synchronize

Exchange Integration mode in MAXCS

4. Configure the names of each extension user such that the first and last names are

the same as the user’s matching mailbox on the Exchange Server.

Note:

The

Middle Initial

field should be

empty

for Exchange Server mail accounts

in order for Exchange integration to work properly.

5. MAXCS matches the mailbox on the Exchange Server via the display name, which is

a combination of “FirstName LastName”. In the example in Figure 154, the display
name is “Michael Wang”, so you should make sure the user’s display name on the
Exchange Server is “Michael Wang”, or synchronization will fail.

Figure 154. First name and last name in MAXCS must match the display name in

Exchange Server, or synchronization will fail. (Also, to synchronize MAXCS
voice mail with Exchange voice mail in Bridged Access mode, you must have
checked the

Enable Synchronization

check box in the Voice Mail

configuration screen.)

Note:

Exchange Native VM integration uses the extension number and the
extension’s first and last names to link between MAXCS and Exchange.

Select the Exchange

Integration mode
you are going to use.

Enter the NAME (not

the IP address) of
the Exchange Server

«
...
379
380
381
382
383
...
»

Содержание ACC 6.7















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ACC 6.7

Бренд: Razberi Страницы: 113

Бренд: IBM Страницы: 128

SuperServer 1026T-M3

Бренд: Supero Страницы: 104

Server 3100 series

Бренд: Digital Equipment Страницы: 71

Бренд: IOGear Страницы: 44

Compaq AlphaServer DS10

Бренд: HP Страницы: 43

Cluster Platform Hardware Kits v2010

Бренд: HP Страницы: 12

Бренд: HP Страницы: 12

hpe proliant dl20 gen9

Бренд: HP Страницы: 131

Cisco MDS 8/12c

Бренд: HP Страницы: 44

Cluster Platform

Бренд: HP Страницы: 74

Cisco MDS 8/24c

Бренд: HP Страницы: 44

Cluster Platform

Бренд: HP Страницы: 88

HPE ProLiant DL180 Gen10

Бренд: HP Страницы: 157

HPE ProLiant DX360 Gen10

Бренд: HP Страницы: 187

Apollo 2000 System

Бренд: HP Страницы: 178

Color LaserJet Enterprise CP5525

Бренд: HP Страницы: 8

Apollo 4200 Gen9

Бренд: HP Страницы: 193

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды