manualshive.com logo in svg

Altigen ACC 6.7, Руководство администратора, Страница: 28 / 462

Поделиться
Скачать
Altigen ACC 6.7 Скачать руководство пользователя страница 28

Chapter 1:  Overview

14

  MAXCS ACC 6.7 Administration Manual

VoIP Hop-Off Call Support

 - allows an extension to access a PSTN trunk on the remote 

system and “hop off” to dial an outside telephone number. This hop off feature can be 
enabled or disabled on the remote system. Outcall restrictions for hop off calls are 
configurable.

SIP Trunk Support

 - MAXCS enables AltiGen’s system to connect to IP-based trunking 

service providers via SIP. 

SIP NAT Traversal 

- Allows MAXCS to connect to a remote SIP phone or IPTalk behind 

NAT without changing the NAT setting at the remote location.

Support for RFC 2833 (DTMF payload embedded with RTP)

 - Supported in SIP 

trunks only. This feature helps to resolve DTMF tone detection and regeneration when 
using G.723.1 or G.729 codec. Basically low bit rate compression will distort DTMF tone 
during compression. The far end device may not be able to recognize the DTMF digits. 
RFC 2833 specifies a separate RTP payload format to carry DTMF information to ensure 
the other side can recognize the tone properly.

Support for both SIP and H.323 Tie Trunk

 - When setting up a system-to-system 

VoIP tie trunk, either SIP or H.323 protocol can be used.

Multi-Site VoIP Management - Enterprise Manager

Multi-site management through Enterprise Manager includes:

VoIP domain 

- when networking multiple AltiGen systems from different sites, one 

system can be assigned as VoIP domain controller to propagate configuration data to 
member systems.

Directory Synchronization

 - when a new extension is added to one of the member 

systems and configured as Global extension, the VoIP domain controller will propagate 
this extension to all member systems. Every member system within the VoIP domain will 
be able to see the extension number plan of other systems.

Multi-site Call Routing

 - when a user dials an extension number that is not a local 

extension number, the system will search the Domain extension list. If a list is found, 
the system will dial the number by using the IP address and extension number stored in 
the Domain extension list.

Domain User Management

 - The VoIP domain controller can resolve the conflict if 

duplicated extension numbers are created in different member systems. This feature 
also manages extension relocation. When an extension user is relocated to another 
member system, its voice mail and greeting can be moved along with it.

Global Least Cost Routing 

- when multiple systems are in different area codes or 

countries, the administrator can set up Global Least Cost Routing to route long distance 
or international calls through member systems. The routing rules are propagated to all 
members automatically.

Global Dial-by-Name and Greeting Synchronization

 - Caller using the dial-by-name 

feature from any system within the VoIP domain can search the entire global directory. 
The global extension’s greeting is replicated to all systems within the VoIP domain. 

Global Extension Relocation by User

 - When a global extension user travels to any 

site, the user can dial #27 to log in to the local server. AltiEnterprise relocates the user’s 
extension setting and voice mail to the local server and activates the extension as a 
physical extension. All member systems receive an update notice from Enterprise 
Manager to change the routing destination. 

Global DID Number List

 - The DID number field is part of the global extension 

configuration. When a call comes in with a DID number, the system looks for a local 
extension with the same DID number first. If the system cannot find a matching local 
extension, it will match the global extension DID number and route the call. 

Содержание ACC 6.7















































































































































































































































































































































































































































































Отзывы:

Нет отзывов