manualshive.com logo in svg

Altigen ACC 6.7, Руководство администратора, Страница: 355 / 462

Поделиться
Скачать
Altigen ACC 6.7 Скачать руководство пользователя страница 355

MAXCS ACC 6.7 Administration Manual  341

C

H A P T E R

26

Redundancy Configuration

MAX Communication Server 6.7 provides for system redundancy (a Redundancy license 
is required). Two Softswitch servers, primary and secondary, must be set up and 
connected through a Dataprobe A\B switch box (KAB). The two servers maintain a keep-
alive connection between them directly, AltiServ to AltiServ. When the active server goes 
down, the standby server takes over control. The change is transparent to direct 
connected calls. (See “How Calls Are Affected When Switchover Occurs” on page 343.)
The primary and secondary servers must be located in the same LAN, and they must 
share the same public IP addresses, so that external services and applications can 
connect, no matter which server is handling the traffic.
The minimum configuration for system redundancy consists of the primary Softswitch, 
the secondary Softswitch, gateways, Voice Mail server, External Logger, and CDR 
database systems. See Figure 140, “Redundancy topology".

Содержание ACC 6.7















































































































































































































































































































































































































































































Отзывы:

Нет отзывов