Altigen ACC 6.7 Скачать руководство пользователя страница 223

Страница: 223 / 462

Chapter 15: Extension Configuration

MAXCS ACC 6.7 Administration Manual 209

Figure 105. Extension Configuration, One Number Access tab

One Number Access Options

In the

One Number Access

tab, use the drop-down list to select an option for One

Number Access:

•

Disabled

•

Enabled at any time

•

Enabled during business hours only

•

Enabled during non-business hours

•

Enabled based on schedule

If you select this last option,

Enabled based on schedule

, you can then select and set

up to four different time periods using the

From

and

time drop-down lists.

After choosing any of the enabling options, you set the

Verify Caller ID

and

Forwarding

choices, and these are discussed below.

Note:

You can also enable and set up One Number Access remotely through
MaxCommunicator.

Disabling One Number Access

You can disable ONA for the extension by selecting the

Disable

option. Selecting

Disable

on this tab does not destroy the data you might have entered. For example, if

you entered a group of Caller IDs to use to identify the caller, these will be available if
you enable one number access at a future time.

Содержание ACC 6.7















































































































































































































































































































































































































































































Результаты поиска

Содержание ACC 6.7

Отзывы:

Похожие инструкции для ACC 6.7

Бренды по названию

Популярные бренды

Altigen ACC 6.7, Руководство администратора

Результаты поиска

Содержание ACC 6.7

Отзывы:

Похожие инструкции для ACC 6.7

Бренды по названию

Популярные бренды