manualshive.com logo in svg

Altigen ACC 6.7, Руководство администратора, Страница: 228 / 462

Поделиться
Скачать
Altigen ACC 6.7 Скачать руководство пользователя страница 228

Chapter 16:  Setting Up IP Extensions

214

  MAXCS ACC 6.7 Administration Manual

Figure 108.  Signaling and media channel between two IP phones

Signaling Channel

—A SIP signaling channel communicates between the system and 

the IP phone to perform call control, including call setup, tear down, registration, and 
phone feature access. The signaling channel implementation consists of the following 
elements:

•

SIP Virtual Board

—Establishes a logical board ID relationship with other types of 

physical boards in the system (displayed on Board View window as SIPSP board).

•

SIP Signaling Channel

—Creates SIP signaling channels for IP Extensions (access 

through SIPSP board, Channel Group configuration).

Содержание ACC 6.7















































































































































































































































































































































































































































































Отзывы:

Нет отзывов