Alstom SHPM 101 Скачать руководство пользователя страница 87

Страница: 87 / 336

SERVICE MANUAL

R5888C

QUADRAMHO

Chapter 2

Page 25 of 74

When a test option is selected (or an invalid scheme) the “relay inoperative” alarm
contact will close and the “relay available” LED will extinguish.

The full schemes do not run when a test option is selected. Below is a list of the
features that are run when a test option is selected:

a) Digital synchronous polarising.
b) Pole dead logic.
c) Master reset pulse on “All Poles Dead” conditions.
d) Band pass filter switching logic.

Test

LED

option

Test and method

indications

Comments

no.

Zone 1 comparators gated A–N

Amplitude and

with low set current

B–N

angular hysteresis

level detectors

C–N

operate on any
Zone 1 comparator.

(Secondary Inject

A–B

No tripping will

Zone 1 Fault)

B–C

occur

C–A

AIDED TRIP

Breaker open opto input
(Apply rated volts to A3–A4)

SOTF

Reset Zone 1 extension opto
input (Apply rated volts to

V~ FAIL

A1–A2)
The “Zone 1 extension” opto is
redesignated as “miniature
circuit breaker open” opto
when this version has been
supplied.

Zone 2 comparators gated A–N

Amplitude and

with low-set current

B–N

angular hysteresis

level detectors

C–N

operate on any

(Secondary inject

A–B

Z2 comparator

Zone 2 fault)

B–C

No tripping will

C–A

AIDED TRIP

occur.

Signal receive opto input
(Apply rated volts to A9–A10)

SOTF

Channel in service opto input

V~ FAIL

(Apply rated volts to A7–A8)
The “signal receive” opto also
can be used to “reset Zone 1
extension” for the appropriate
thumbwheel selection option,

Содержание SHPM 101

















































































































































































































































































































































Результаты поиска

Содержание SHPM 101

Отзывы:

Бренды по названию

Популярные бренды

Alstom SHPM 101, Руководство по обслуживанию

Результаты поиска

Содержание SHPM 101

Отзывы:

Бренды по названию

Популярные бренды