manualshive.com logo in svg

Alstom SHPM 101, Руководство по обслуживанию

Поделиться
Скачать
Alstom SHPM 101 Скачать руководство пользователя страница 290

SERVICE MANUAL

R5888C

QUADRAMHO

Chapter 6

Page 2 of  12

self-check on Zone 1 comparators via the top six LED. A failure is indicated by a
LED being off. Repeat for Zone 2 by selecting option 46 and Zone 3 by option 47.
In this option the LED “SOTF” represents the power swing blocking comparator. If a
failure is detected the detailed tests in Section 5.3 must be carried out.

Remove the dc supply and extract module 1 (RRZ 07), insert the double extender
card in the left hand position and connect edge connector AA33 to pin 16 of the
monitor point box which should be plugged in. Do not replace the module. Turn
the dc supply on and check the relay available LED. If the LED is illuminated,
replace module 1 (RRZ 07) otherwise replace module 2 (RRM 08).

Section 3

QUICK FAULT FINDING GUIDE

If a spare set of modules is available a method of substitution may be used to
locate a faulty module. This method is often quicker and requires no extra
equipment.

The following table may be used as a guide:

Fault symptom

Module most likely to be faulty

Any element in Zone 1/2 inaccurate

Module 2

RRM 08

but Zone 3 alright.

Any element in Zone 3 inaccurate

Module 3

RRM 09

but Zone 1/2 alright.

Ground fault reach low

Module 1

RRZ 07

in all zones.

Phase fault reach low

Module 1

RRZ 07

in Zone 1/2.

No operation for elements

Module 1

RRZ 07

involving a common phase.

Reach equally inaccurate

Module 5

RFV 04

all zones.

No operation for three

Module 2

RRM 08

phase close up faults.

Section 4

TEST PROCEDURE

4.1

Test equipment required

Quadramho accessory kit 01.

Test set.

1 interval timer (one that can work off contacts or 24V levels and has a dwell

facility).

2 multimeters (20,000 ohms per volt on dc range).

Single channel oscilloscope with X 10 probe or frequency meter.

2 single pole switches.

Содержание SHPM 101

















































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды