manualshive.com logo in svg

Alstom SHPM 101, Руководство по обслуживанию

Поделиться
Скачать
Alstom SHPM 101 Скачать руководство пользователя страница 23

SERVICE MANUAL

R5888B

QUADRAMHO

Chapter 1

Page 7 of 27

For ground faults on multiple-earthed systems, it is possible, due to healthy phase
current levels, for the magnitude of the greatest phase difference current to be
larger than the neutral current at the relaying point. It is extremely unlikely,
however, for the ratio of these two currents to exceed the level of 10, which would
need to be reached before the low-set neutral detector failed to operate for a
ground fault.

Section 15.

SELECTION OF SCHEME LOGIC PROGRAMS

The distance scheme logic programs are selected by setting two coded selector
switches to a particular two-digit number. A list of scheme codings is given in
Chapter 2.

Section 16.

SETTING OF SCHEME OPTION SWITCHES

SW1

(LEFT)

SOTF tripping initiated by comparators

(RIGHT)

SOTF tripping initiated by level detectors

SW2

(LEFT)

SOTF enable time = 110s

(RIGHT)

SOTF enable time = 200ms

SW3

(LEFT)

VTS indicates only

(RIGHT)

VTS indicates and blocks relay

SW4

(LEFT)

Normal block autoreclose action

(RIGHT)

Block autoreclose also for Z1 and aided trip 3 phase faults

SW5

(LEFT)

Self checking feature disabled

(RIGHT)

Self checking feature enabled

SW6

(LEFT)

Normal block autoreclose

(RIGHT)

Block autoreclose also for signalling channel out of service

SW7

(LEFT)

Disable trip by weak infeed feature

(RIGHT)

Enable trip by weak infeed feature

SW8

(LEFT)

POR weak infeed feature disabled

(RIGHT)

POR weak infeed feature enabled

SW9

(LEFT)

Power swing blocking function disabled

(RIGHT)

Power swing blocking function enabled

Section 17.

DISCUSSION ON APPLICATION OF VARIOUS DISTANCE
SCHEME OPTIONS

17.1

Basic (see Figure 3)

• This scheme does not require signalling channels.

• A major disadvantage is that not all the faults within a protected section

can be cleared instantaneously by distance relays at both ends.

• Scheme is suitable for a single circuit radial line where a distance relay

would be used at the source end only.

Содержание SHPM 101

















































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды