manualshive.com logo in svg

Alstom SHPM 101, Руководство по обслуживанию

Поделиться
Скачать
Alstom SHPM 101 Скачать руководство пользователя страница 232

SERVICE MANUAL

R5888C

QUADRAMHO

Chapter 5

Page 12 of  24

given. If set for blocking this can take place instantaneously if a comparator
operates.

4.13.1 Operation on zero sequence volts

Apply balanced 3 phase-neutral volts and reduce the voltage on one phase until
V~FAIL indication is obtained.

The operation time is 5.5s (tolerance 

±

0.1s). The zero sequence voltage setting is

15% of 63.5V, thus the required voltage reduction on one phase is 45% of 63.5V
(28.6V tolerance 

±

20%). The phase-neutral voltage required for operation should

thus be between (70% of V

N

). (For 60Hz the limits are 27 to 46 volts).

4.13.2 Timing check

Timing is checked by using a double pole switch to remove one healthy voltage
and start a timer which is stopped by the alarm contacts (C17–18). The time
obtained should be stated as above.

4.13.3 Current checks

The zero sequence current level detector has already been checked for its
operation level (Section 4.4), thus it is now only necessary to inject a current
above this low set neutral level into one phase while one phase-neutral voltage is
below (70% of V

N

) and to check that the V~Fail indication can be reset. It is

recommended that the variac and resistor are used for supplying the current when
a ZFB is used to supply the volts. Check that when V~Fail is indicated, that moving
SW3 to the right causes the relay available LED to extinguish.

4.13.4 Instantaneous indication or blocking check

Conect the relay as if an A–G fault were to be applied, but instead of returning the
current through the neutral take it in the reverse direction through B phase.
(The current path is into 1Y1 out of 1Y2 link to 1Y4 out of 1Y3, all being the relay
side terminals of the lower test block). The result of this is that fault application will
not produce any residual current. Choose the source and fault impedance such that
when the fault is applied, the A–N volts will fall below 25 volts, causing the zero
sequence voltage level detector to pick up.

To be sure of getting a Zone 1 comparator operating (A–B) set K11 to 

∞

. SW3

should still be set to the left. Apply the fault and instantaneous indication will be
obtained for an A–B fault and V~Fail.

Set SW3 to the right and apply the fault until time delayed V~Fail indication only is
obtained.

Set SW3 in the required position and return K11 to the correct setting.

Note:

When 

∞

 is selected the comparator self-check may cause the relay

available LED to go off.

4.13.5 Miniature circuit breaker block check

Energise the opto coupler connected to case terminals A1 and A2. (Zone 1
extension reset opto on non-MCB versions of Quadramho). Check the following:

i) The VT indication operates and latches.

ii) The 97X–1 contact on case terminals C17 and C18 closes.

iii) The relay available green LED extinguishes.

iv) The relay inoperative alarm 97Y–1 on case terminals C21 and C22 opens.

Содержание SHPM 101

















































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды