manualshive.com logo in svg

Alstom SHPM 101, Руководство по обслуживанию

Поделиться
Скачать
Alstom SHPM 101 Скачать руководство пользователя страница 281

SERVICE MANUAL

R5888B

QUADRAMHO

Chapter 5

Addendum 3

Page 1 of 1

NEW RECOMMENDATIONS FOR TIMER SETTINGS
IN THE CURRENT REVERSAL GUARDS

Permissive Overreach Scheme 04 or 05

If the current reversal guard is not required, ie there is no parallel line or the
Zone 2 reach is not set to more than 150% of the line length, then set tD = 0 and

tp = 90ms.
If the guard is required, recommended tp = 30ms – minimum signalling channel

operating time.

(The nearest available setting should be selected if the exact value is not
available).

To give satisfactory scheme operation the value selected for tp must also be

less than mimimum time from fault inception to current reversal minus
(30ms + maximum signalling channel operating time).

Recommended tD – 25ms + maximum signalling channel reset time.
(The nearest available setting above should be selected if the exact value is not
available).

Blocking Scheme 06 or 07

Recommended setting for tp = maximum signalling channel operating time + X
(The nearest available setting above should be selected if the exact value is not
available).

X = 30ms for quadrilateral/mho version of the relay.

= 35ms for mho/lenticular (a/b = 1).

= 40ms for mho/lenticular (a/b = 0.69).

= 45ms for mho/lenticular (a/b = 0/41).

Recommended setting for tD = 25ms – minimum signalling channel reset time.
(The nearest available setting above should be selected if the exact value is not
available).

Note: The new recommendation for tD is to bring it in line with the approval

panels results on SHNB (Micromho Protection) that where a single
frequency signalling channel is used, during current reversals the block
signal to the relay should be continuous until the external fault has been
cleared.

Содержание SHPM 101

















































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды