manualshive.com logo in svg

Alstom SHPM 101, Руководство по обслуживанию

Поделиться
Скачать
Alstom SHPM 101 Скачать руководство пользователя страница 298

SERVICE MANUAL

R5888C

QUADRAMHO

Chapter 6

Page 10 of  12

5.3

Self checking

Remove the dc and ac supplies from the relay and select option 00 and SW5 to
the right. Reconnect the dc and check the relay available LED is on. Connect the
three phase-neutral voltages and ensure they are each above 50V. Press the reset
pushbutton. Select option 45. If all 8 LEDs are on, a self check has not been
performed. In this case check the voltage level detectors as in Section 5.4. If they
are correct replace module 4 (RCL 10). If all 8 LEDs in option 45 are not on, use
the information in Figure 1 to determine which if any of the 6 Zone 1 comparators
have failed. Select option 46 and 47 to check the Zone 2 and the Zone 3/6
comparators respectively. Replace module 2 (RRM 08) if any element in Zone 1 or
2 failed or module 3 (RRM 09) if any element in Zone 3/6 failed.

5.4

Voltage circuit checks

These tests are designed to locate a fault in the voltage circuits. They must be done
in the order shown in flow chart 5, Addendum A of this Chapter.

Remove all the ac voltages, select option 43 and check LED A, B and C are off.

Apply balanced rated voltage, select option 43 and check LED A, B and C are on.

Apply balanced rated voltage, select option 42 and check LED SOTF is off.

Apply balanced rated voltage, select option 42, remove each voltage one at a
time and check LED SOTF is on.

Apply balanced rated voltage, select option 53, connect a multimeter on an ac
voltage range greater than 24V to pins 24 and 2 (0V) of the 25 way monitor point
box. Check the multimeter reads approximately 12V. Remove C phase voltage and
check multimeter reads approximately 0V.

Select option 00, connect link 1Z 10 and check relay available LED is on.

Repeat test 2.7.

5.5

Current level detector checks

These tests are to be done in the order given. Flow chart 6 can be used to identify
a faulty module.

Select option 53 and check the bottom four LEDs are off. If LED Z3, Aided trip or
SOTF are on, replace module 4 (RCL 10). If LED V~Fail is on remove module 1.
If the LED remains on replace module 4 otherwise replace module 1 (RRZ 07).

Select option 43 and check the bottom four LEDs are off. If the V~Fail LED is on
remove module 3 (RRM 07) or if LED Z3, aided trip or SOTF are on remove
module 1 (RRZ 07). If the LED remains on replace module 4 (RCL 10) otherwise
replace the module that has been removed.

Check the six fixed current level detectors and the two auto-ranging level detectors
as in Section 4.10.

5.6

Current input module checks

The output from the current input module may be monitored by removing module 1
and inserting a double extender card in the right hand position. The right hand
board can be inserted leaving the left hand one unconnected. One multimeter is
used to measure the primary current, the other the transphasor and the transformer
(Quadrilateral version only) output voltages at the test points given in the table
below. Inject current into each phase in turn and check the output voltages
according to the following formulae.

Содержание SHPM 101

















































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды