manualshive.com logo in svg

Alstom SHPM 101, Руководство по обслуживанию

Поделиться
Скачать
Alstom SHPM 101 Скачать руководство пользователя страница 10

Before energising the equipment it must be earthed using the protective earth
terminal, or the appropriate termination of the supply plug in the case of plug
connected equipment. Omitting or disconnecting the equipment earth may cause a
safety hazard.

The recommended minimum earth wire size is 2.5 mm

2

, unless otherwise stated in

the technical data section of the product documentation.

Before energising the equipment, the following should be checked:

Voltage rating and polarity;

CT circuit rating and integrity of connections;

Protective fuse rating;

Integrity of earth connection (

where applicable)

Equipment operating conditions

The equipment should be operated within the specified electrical and
environmental limits.

Current transformer circuits

Do not open the secondary circuit of a live CT since the high voltage produced
may be lethal to personnel and could damage insulation.

External resistors

Where external resistors are fitted to relays, these may present a risk of electric
shock or burns, if touched.

Battery replacement

Where internal batteries are fitted they should be replaced with the recommended
type and be installed with the correct polarity, to avoid possible damage to the
equipment.

Insulation and dielectric strength testing

Insulation testing may leave capacitors charged up to a hazardous voltage. At the
end of each part of the test, the voltage should be gradually reduced to zero, to
discharge capacitors, before the test leads are disconnected.

Insertion of modules and pcb cards

These must not be inserted into or withdrawn from equipment whilst it is energised,
since this may result in damage.

Fibre optic communication

Where fibre optic communication devices are fitted, these should not be viewed
directly. Optical power meters should be used to determine the operation or signal
level of the device.

Содержание SHPM 101

















































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды