manualshive.com logo in svg

Alstom SHPM 101, Руководство по обслуживанию

Поделиться
Скачать
Alstom SHPM 101 Скачать руководство пользователя страница 238

SERVICE MANUAL

R5888C

QUADRAMHO

Chapter 5

Page 18 of  24

Switch SW6 controls whether or not auto reclose is blocked when the channel is
out of service.

If SW6 is set to the right, check that the block auto reclose contact (Terminals
B25–26) is closed when the channel in service opto isolator is not energised.
Check that energising the opto isolator causes the contact to open. If SW6 is set to
the left, check that the contact does not close for either state of the opto isolator
input.

Note:

that if the channel is out of service, the relay reverts to a basic scheme.

5.4

Permissive overreach scheme (04 or 05)

Note:

that if the channel in service opto isolator input is not energised, three
phase trips will be given in scheme 04.

Commence tests with the weak infeed feature out (SW8 to the left). Connect a
double pole switch so that one pole can be used to energise the signal receive
opto isolator input (terminals A9(+) – A10) and the other pole to start a timer.

5.4.1

Aided trip check

In this scheme Zone 2 comparator operation causes signal send and an
instantaneous aided trip is obtained by Zone 2 comparator operation plus signal
receive.

Apply a Zone 2 fault and check a trip is obtained in the set Zone 2 time.

Energise the optical isolator and re-apply the Zone 2 fault; check that aided trip
indication is obtained immediately and that the alarm contact (C13–14) closes.

5.4.2

Signal send check

Check that the signal send contacts (B1–B2, B3–B4) close immediately a Zone 2
fault is applied

Test option 62 can also be made to close the signal send contacts, check that with
SW8 to the right; pressing the reset button causes the contacts to close. This will be
used in the signalling channel check later.

Note that other contacts may operate depending on the other SW switch positions.

5.4.3

Measurement of t

p

The current reversal guard in the scheme is initiated when a healthy circuit relay
receives a permissive trip signal; however a certain delay t

p

 is required to give

time for a Zone 2 comparator to pick up.

The recommended setting for t

p

 is 30ms minus channel pick up or the nearest

available higher setting.

Due to processing times and the point on the program loop when a signal is
applied, the measured times vary as follows:

t

p

 = 0 or 6

10 to 15ms

t

p

 = 12

15 to 20ms

t

p

 = 18

21 to 26ms

t

p

 = 24

27 to 34ms

The time is measured from the closing of the switch energising the signal receive
opto isolator to the signal receive enunciate on the monitor point box terminals 2(–)
to 9(+) going from 24V to zero.

Содержание SHPM 101

















































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды