manualshive.com logo in svg

Allen-Bradley 1763-L16AWA, Справочник по набору инструкций

Поделиться
Скачать
Allen-Bradley 1763-L16AWA Скачать руководство пользователя страница 536

Publication 1763-RM001C-EN-P - October 2009

536

        Protocol Configuration

Ethernet Driver

The MicroLogix1100 supports Ethernet communication via the Ethernet 
communication channel 1. Ethernet is a local area network that provides 
communication between a variety of network devices at 10/100 Mbps.

TCP/IP is the mechanism used to transport Ethernet messages. The 
MicroLogix1100 processor uses TCP/IP to establish sessions and to send 
MSG commands. Connections can be initiated by either a client program 
(INTERCHANGE or RSLinx application) or a processor. Refer to 
Communications Instructions on page 341 for the MSG instruction 
operation to see how connections are established using the MSG 
instruction. The MicroLogix1100 Ethernet connector conforms to ISO/IEC 
8802-3 STD 802.3 and utilizes 10/100Base-T media. Connections are made 
directly from the MicroLogix1100 to an Ethernet hub or switch. The 
network setup is simple and cost-effective.

There are two ways to configure the MicroLogix1100 Ethernet channel 1. 
The configuration can be done via a BOOTP or DHCP request at 
processor power up, or by manually setting the configuration parameters 
using RSLogix 500 Programming Software (refer to Example 5 - 
Configuring an Ethernet/IP Message on page 381). 

Ethernet Configuration Parameters

Parameter

Options

Programming 
Software Default

Driver

Ethernet

Ethernet

Hardware 
Address

The processor's Ethernet hardware address. This value cannot be changed.

Ethernet Hardware 
Address

IP Address

1 to 254 (zero and 255 are reserved for broadcast purposes.)

The processor's internet address. You must specify the IP address to enable the processor to connect 
to the TCP/IP network. You can specify the address manually, or enable BOOTP or DHCP (located in 
the Protocol Control section of this dialog) to provide the address.

0.0.0.0

Subnet Mask

0 to 255 in each field.

Used by the processor to interpret IP addresses when the Internet is divided into subnets. The subnet 
mask must be specified. You can do this either manually or by enabling BOOTP or DHCP.

The processor compares and screens addresses using the mask to identify its own address to see if it 
should listen to corresponding messages. The comparison occurs in binary. Any address position for 
which the mask is set to a binary 1 will be compared; any address position for which the mask is set to 
a binary 0 will be ignored. For example, if the mask is 255.255.255.0 the processor will listen to all 
addresses whose first three segments match its own address regardless of the value in the last 
segment. (255 in decimal equals to 1111 1111 in binary.)

0.0.0.0

Gateway 
Address

1 to 254 in each field.

The IP address of the gateway that provides a connection to another IP network. This field is required 
when you communicate with other network devices, not on a local subnet.

0.0.0.0

efesotomasyon.com - Allen Bradley,Rockwell,plc,servo,drive

Содержание 1763-L16AWA









































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды