Agilent Technologies n5181a Скачать руководство пользователя страница 69

Страница: 69 / 202

Agilent N5161A/62A/81A/82A/83A MXG Signal Generators Service Guide

Troubleshooting

The RPG Knob is Not Functioning (N5181A/82A/83A)

1-61

Figure 1-29 A3J6 and A3J10

If the RPG test fails, complete the following procedure to determine the faulty assembly/part:

Remove the front panel. Refer to

Chapter 3, "Assembly Replacement"

Refer to

Figure 1-28

. Verify that A6J2-25 has a voltage of +3 Vdc:

•

If A6J2-25 has a voltage of +3 Vdc, go to

step 10

•

If A6J2-25 does not have a voltage of +3 Vdc, go to

step 3

Refer to

Figure 1-28

. Measure A6J1-11 and A6J1-12; they should have a voltage of +3 Vdc.

•

If A6J1-11 and A6J1-12 have a voltage of +3 Vdc, replace the A6 DC-AC Inverter Interface Board.

•

If A6J1-11 and A6J1-12 do not have a voltage of +3 Vdc, go to

step 4

Refer to

Figure 1-29

. Measure A3J6-11 and A3J6-12; they should have a voltage of +3 Vdc.

•

If A3J6-11 and A3J6-12 have a voltage of +3 Vdc, replace the W1 ribbon cable.

•

If A3J6-11 and A3J6-12 do not have a voltage of +3 Vdc, go to

step 5

Refer to

Figure 1-29

. Measure A3J10-A21 and A3J10-A22; they should have a voltage of +3 Vdc.

•

If A3J10-A21 and A3J10-A22 have a voltage of +3 Vdc:

Replace the A3 RF assembly.

After replacing the A3 RF assembly in a model N5183A instrument, go to

Chapter 4, "Post-Repair Procedures and Performance

Verification"

•

If A3J10-A21 and A3J10-A22 do not have a voltage of +3 Vdc, go to

“A1 Power Supply” on page 1-26

to troubleshoot the A1

Power Supply.

Refer to

Figure 1-28

. Measure A6J2-28; it should have a voltage of +5 Vdc.

•

If A6J2-28 has a voltage of +5 Vdc, go to

step 10

•

If A6J2-28 does not have a voltage of +5 Vdc, go to

step 7

A3J611 and A3J6-12

A3J10-A21 and A3J10-A22

Front Panel

Rear Panel

Front Panel

A3J6-3 and A3J6-4

A3J10-B16

深圳德标仪器

135-1095-0799

Содержание n5181a











































































































































































































Результаты поиска

Содержание n5181a

Отзывы:

Agilent Technologies n5181a, Руководство по обслуживанию, Страница: 69 / 202

Результаты поиска

Содержание n5181a

Отзывы: