Agilent Technologies n5181a Скачать руководство пользователя страница 185

Страница: 185 / 202

Agilent Technologies N5161A/62A/81A/82A/83A MXG Signal Generators Service Guide

Post-Repair Procedures and Performance Verification

Post Repair Procedures

4-5

If a manual performance verification test fails:

Verify that the test setup is correct.

•

For I/Q Calibration and Self Tests

— Confirm that all external cables, including GPIB, LAN, and USB cables, are disconnected from the signal generator.

•

For Relative Frequency Range and Accuracy Verification

— Verify that the cables are connected correctly.

— Verify that the spectrum analyzer is set to external reference.

•

For Leveled Output Accuracy Verification

— Verify you are using the appropriate power sensor.

— Normally, power sensor calibration factors are automatically downloaded to the power meter when the power meter turns on. If

this does not occur, manually enter the correct calibration factors for the power sensor you are using.

— Verify the power sensor is properly calibrated to the power meter.

If the tests setups are correct, go to

“Troubleshooting Performance Test Problems” on page 1-72

Table 4-3 Manual Performance Tests

Manuals Performance Tests

The following performance verification tests are listed in
the order that they should be performed.

Replaced Assembly

Key Pad

D Display

DC-A

rte

r In

terf

ace

A1 Power

A2 V

tor M

le (N5162A/82A only)

A3 RF Assem

ly (N5183A

ly)

A4 Me

mory Chip

(

5162A/82A on

ly)

A5 CPU

I/Q Calibration (N5162A/82A only)

? ?

Self Tests

? ? ? ? ? ?

? ?

Relative Frequency Range and Accuracy Verification

? ?

Leveled Output Power Verification

? ?

0Phase Noise (N5183A only)

The phase noise test procedure is available as part of the N5183A calibration software.

深圳德标仪器

135-1095-0799

Содержание n5181a











































































































































































































Результаты поиска

Содержание n5181a

Отзывы:

Agilent Technologies n5181a, Руководство по обслуживанию, Страница: 185 / 202

Результаты поиска

Содержание n5181a

Отзывы: