manualshive.com logo in svg

Agilent Technologies n5181a, Руководство по обслуживанию, Страница: 122 / 202

Поделиться
Скачать
Agilent Technologies n5181a Скачать руководство пользователя страница 122

Agilent N5161A/62A/81A/82A/83A MXG Signal Generators Service Guide

 

 

Assembly Replacement
Front-Panel

3-10

Front-Panel 

Tools Required 

•

T-20 driver 

•

needle-nose pliers

Removal Procedure

Refer to 

Figure 3-4

 for this procedure. 

1.

Disconnect the power cord.

2.

Remove the covers from the signal generator. Refer to 

”Outer Cover” on page 3-4

, 

”Inner Top Cover” on page 3-6

, and 

”Inner Bottom 

Cover” on page 3-8

.

3.

With the signal generator on its side, disconnect W1 and W2 from the A3 RF assembly by squeezing the cable connector and pulling the 
cable away from the signal generator.

4.

Release W2 from the cable clips.

5.

For N5182A instruments, place the signal generator flat with the A2 Vector Module facing you and use the needle-nose pliers to 
disconnect the following cables,

•

W3 (I Input) from A2J15

•

W4 (Q Input) from A2J16

6.

Remove the chassis grommet before pulling W3 and W4 thru the chassis (N5182A only).

7.

With the signal generator upside down and flat, use the T-20 driver to remove the four screws (1) from the sides of the chassis

CAUTION

Before removing the front-panel from the signal generator, lift and support the front frame of the signal generator. 

8.

Slide the front-panel over the RF output connector (N5181A/82A/83A standard models only).

9.

Remove the front-panel.

Replacement Procedure 

1.

Reverse the order of the removal procedure.

2.

Torque all screws to 21 in–lbs.

3.

Perform the post-repair performance tests that pertain to this replacement procedure, see 

Chapter 4, Post-Repair Procedures and 

Performance Verification

.

深圳德标仪器 

135-1095-0799

Содержание n5181a











































































































































































































Отзывы:

Нет отзывов