Agilent Technologies n5181a Скачать руководство пользователя страница 120

Страница: 120 / 202

Agilent N5161A/62A/81A/82A/83A MXG Signal Generators Service Guide

Assembly Replacement
Inner Bottom Cover

3-8

Inner Bottom Cover

Tools Required

•

T-10 driver

Removal Procedure

Refer to

Figure 3-3

for this procedure.

Disconnect the power cord.

Remove the outer-cover from the signal generator. Refer to

”Outer Cover” on page 3-4

Place the signal generator flat with the front-panel facing you.

Using the T-10 driver, remove the eleven flat-top screws (1) from the inner bottom cover (2).

Using the T-10 driver, remove the screw (3) from the rear panel.

Remove the inner bottom cover.

Replacement Procedure

Reverse the order of the removal procedures.

Torque all screws to 9 in–lbs.

深圳德标仪器

135-1095-0799

Содержание n5181a











































































































































































































Результаты поиска

Содержание n5181a

Отзывы:

Agilent Technologies n5181a, Руководство по обслуживанию, Страница: 120 / 202

Результаты поиска

Содержание n5181a

Отзывы: