Agilent Technologies n5181a Скачать руководство пользователя страница 54

Страница: 54 / 202

Agilent N5161A/62A/81A/82A/83A MXG Signal Generators Service Guide

Troubleshooting
No Output Power or Output Power is Unleveled (N5183A)

1-46

Low Output Power or No Output Power >= 3.2 GHz (N5183A)

Remove the external cover and the top inside cover. Refer to

Chapter 3, "Assembly Replacement"

for instructions on removing the

instrument covers.

Using

Figure 1-18

, remove the W13 semirigid cable between the A3 RF output assembly and the 20 GHz doubler input located on the

A7 Micro Deck.

Figure 1-18 W13 Semirigid Cable

Connect the A3 RF assembly output (see

Figure 1-18

) through a 10 dB attenuator to a spectrum analyzer.

Set up the spectrum analyzer:

Press

Preset

Set the reference level to +10 dBm.

Set the start frequency to 2.3 GHz.

Set the stop frequency to 5.3 GHz.

Set Trace to Max Hold.

Set up the signal generator:

Press

Preset

Press

SWEEP

Sweep Type List Step

to Step.

Press

Configure Step Sweep

•

Press

Freq Start

2.8

GHz

•

Press

Freq Stop

10.4

GHz

•

Press

# Points

501

Enter.

•

Press

More

Step Dwell

msec

•

Press

Return

Sweep

Freq

Off

to On.

Press

RF On/Off

to On.

Press

AMPTD

> <maximum settable power> >

dBm

Press

AMPTD

ALC Off On

to Off.

W13 semirigid cable

A3 RF assembly output

深圳德标仪器

135-1095-0799

Содержание n5181a











































































































































































































Результаты поиска

Содержание n5181a

Отзывы:

Agilent Technologies n5181a, Руководство по обслуживанию, Страница: 54 / 202

Результаты поиска

Содержание n5181a

Отзывы: