Agilent Technologies n5181a Скачать руководство пользователя страница 128

Страница: 128 / 202

Agilent N5161A/62A/81A/82A/83A MXG Signal Generators Service Guide

Assembly Replacement
A6 DC-AC Inverter Interface Board (N5181A/82A/83A only)

3-16

A6 DC-AC Inverter Interface Board (N5181A/82A/83A only)

Tools Required

•

T-10 driver

Removal Procedure

Refer to

Figure 3-7

for this procedure.

Disconnect the power cord.

Remove the covers from the signal generator. Refer to

”Outer Cover” on page 3-4

”Inner Top Cover” on page 3-6

, and

”Inner Bottom

Cover” on page 3-8

Remove the front-panel from the signal generator. Refer to

”Front-Panel” on page 3-10

Using the T-10 driver, remove the four screws (1) that secure the inverter shield (2) to the A6 DC-AC Inverter Interface Board (3).

Disconnect the W1 ribbon cable (not shown in

Figure 3-7

) from the A6 DC-AC Inverter Interface board (3).

Disconnect the Power Switch cable (4) from the A6 DC-AC Inverter Interface Board (3).

Disconnect the LCD 2 wire cable (5) from the A6 DC-AC Inverter Interface Board (3).

Disconnect the ribbon cable (6) from the A6 DC-AC Inverter Interface Board (3).

Disconnect the LCD flat flex cable (7) from the A6 DC-AC Inverter Interface Board (3).

10. Using the T-10 driver, remove the three screws (8) that secure the A6 DC-AC Inverter Interface Board (3) to the front-panel sub-panel

(9).

11. Remove the A6 DC-AC Inverter Interface Board.

Replacement Procedure

Reverse the order of the removal procedure.

Torque all screws to 9 in–lbs.

Perform the post-repair performance tests that pertain to this replacement procedure, see

Chapter 4, Post-Repair Procedures and

Performance Verification

深圳德标仪器

135-1095-0799

Содержание n5181a











































































































































































































Результаты поиска

Содержание n5181a

Отзывы:

Agilent Technologies n5181a, Руководство по обслуживанию, Страница: 128 / 202

Результаты поиска

Содержание n5181a

Отзывы: