Agilent Technologies n5181a Скачать руководство пользователя страница 182

Страница: 182 / 202

Agilent Technologies N5161A/62A/81A/82A/83A MXG Signal Generators Service Guide

Post-Repair Procedures and Performance Verification
Post Repair Procedures

4-2

Assembly Installation and Removal Overview

Figure 4-1 Hardware Assembly Installation and Removal Softkeys

Utility

> More 2 of 2 > Service

For details on each key, use key help.
Refer to the

User’s Guide

Note:

Each

Remove Assembly

softkey (CPU/RF/BBG/MW) when enabled will display a message in the lower left quadrant of display indicating assembly prepared for

removal or removal has been aborted.

Each

Install Assembly

softkey, when enabled will display a message in the lower left quadrant of display indicating assembly prepared for installation or

installation has been aborted.

N5162A/82A only

N5183A only

Whether a softkey is available

depends on the model of MXG.

Note:

When

pressed, a Confirm
Removal menu
(similar to the one
shown here for the
CPU assembly) is
opened for the RF,
BBG, and MW
assemblies too.

Whether a softkey is available

depends on the model of MXG.

N5162A/82A only

N5183A only

Note:

When

pressed, a Confirm
Install menu (similar
to the one shown
here for the CPU
assembly) is opened
for the RF, BBG, and
MW assemblies too.

深圳德标仪器

135-1095-0799

Содержание n5181a











































































































































































































Результаты поиска

Содержание n5181a

Отзывы:

Agilent Technologies n5181a, Руководство по обслуживанию, Страница: 182 / 202

Результаты поиска

Содержание n5181a

Отзывы: