manualshive.com logo in svg

Agilent Technologies n5181a, Руководство по обслуживанию, Страница: 162 / 202

Поделиться
Скачать
Agilent Technologies n5181a Скачать руководство пользователя страница 162

Agilent N5161A/62A/81A/82A/83A MXG Signal Generators Service Guide

 

 

Assembly Replacement
A3BT1 Battery

3-50

A3BT1 Battery

WARNING

This battery contains lithium. Do not incinerate or puncture this battery. Do not install this battery backwards. To 
dispose of  the battery in a safe manner. Refer to 

”Lithium Battery Disposal” on page 5-2

.  

NOTE

The battery is part of the power off circuitry. Removing the battery will not cause any stored data to be lost.

Tools Required 

•

T-10 driver

•

small common screw driver

Removal Procedure 

Refer to 

Figure 3-28

 for this procedure.

1.

Disconnect the power cord.

2.

Remove the covers from the signal generator. Refer to 

”Outer Cover” on page 3-4

 and 

”Inner Bottom Cover” on page 3-8

.

3.

Place the signal generator flat with the A3 RF assembly facing up and the front-panel towards you.

4.

Using the flat-head screw driver, remove the A3BT1 by leveraging the battery out of its socket.

Replacement Procedure 

1.

Reverse the remaining steps of the removal procedure.

NOTE

To install the battery, the positive side is aligned with the positive sign on the A3 RF assembly’s battery clip.

2.

Perform the post-repair performance tests that pertain to this replacement procedure, see 

Chapter 4, Post-Repair Procedures and 

Performance Verification

.

深圳德标仪器 

135-1095-0799

Содержание n5181a











































































































































































































Отзывы:

Нет отзывов