Agilent Technologies n5181a Скачать руководство пользователя страница 194

Страница: 194 / 202

Agilent Technologies N5161A/62A/81A/82A/83A MXG Signal Generators Service Guide

Post-Repair Procedures and Performance Verification
Leveled Output Power Verification (N5161A/62A

/81A/82A Only)

4-14

Set the amplitude to 13

dBm:

Press

Amplitude

dBm

Configure the power meter for the measurement.

Press the

Frequency Cal Fac

button on the power meter.

Select a power meter channel (if applicable).

Use the arrow keys to enter the frequency at which to measure the power.

Measure the output power level.

10. Repeat steps

through

to measure power at each of the 15 frequencies listed in

Table 4-10

11. Confirm that the measured power levels are within the limits listed in the table.

NOTE

The limit range is due to power meter uncertainty.

538 MHz

0.6dB

675 MHz

0.6dB

850 MHz

0.6dB

1075 MHz

0.6dB

1350 MHz

0.6dB

1700 MHz

0.6dB

2150 MHz

0.6dB

2700 MHz

0.6dB

3400 MHz

0.7dB

4300 MHz

0.8dB

5400 MHz

0.8dB

For serial numbers <MY4818xxxx, US4818xxxx, and SG4818xxxx, the amplitude = 7 dBm

Table 4-10Leveled Output Power Limits (Continued)

Frequency

Limits (dB)

深圳德标仪器

135-1095-0799

Содержание n5181a











































































































































































































Результаты поиска

Содержание n5181a

Отзывы:

Agilent Technologies n5181a, Руководство по обслуживанию, Страница: 194 / 202

Результаты поиска

Содержание n5181a

Отзывы: