Agilent Technologies n5181a Скачать руководство пользователя страница 52

Страница: 52 / 202

Agilent N5161A/62A/81A/82A/83A MXG Signal Generators Service Guide

Troubleshooting
No Output Power or Output Power is Unleveled (N5183A)

1-44

Checking Attenuator Output Signals < 3.2 GHz (N5183A)

Remove the external cover and the top inside cover. Refer to

Chapter 3, "Assembly Replacement"

for instructions on removing the

instrument covers.

Using

Figure 1-16

, remove the attenuator output cable, and connect the attenuator output to the spectrum analyzer. (The attenuator

output connector is a 2.4 mm female connector and requires a cable with a 2.4 mm male connector.)

Figure 1-17 Attenuator output cable

Set up the spectrum analyzer:

Press

Preset

Set the reference level to +25 dBm (or maximum available power).

Set the start frequency to 50 kHz.

Set the stop frequency to 3.2 GHz.

Set Trace to Max Hold.

Set up the signal generator:

Press

Preset

Press

SWEEP

Sweep Type List Step

to Step.

Press

Configure Step Sweep

•

Press

Freq Start

100

kHz

•

Press

Freq Stop

3.1999

GHz

•

Press

# Points

501

Enter.

Attenuator output cable

深圳德标仪器

135-1095-0799

Содержание n5181a











































































































































































































Результаты поиска

Содержание n5181a

Отзывы:

Agilent Technologies n5181a, Руководство по обслуживанию, Страница: 52 / 202

Результаты поиска

Содержание n5181a

Отзывы: