ADC AD-320 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 60

background image

48

American Dryer Corp.

112144 - 46

If the dryer is equipped with the optional rotational sensor and for whatever reason the Dual Microprocessor Controller
(DMC) computer detects that the basket (tumbler) is not turning, it will disable

ALL

of the dryer outputs (shut the

dryer down), and the light emitting diode (L.E.D.) display will read “SEFL.” The L.E.D. display will continue to
read “SEFL” until the DMC computer is manually reset by closing and opening the Program Switch (PS).

Possible causes...

1. Loose/slipping (out of proper adjustment) basket (tumbler) belt.

2. Broken basket (tumbler) V-belt.

3. Failed motor (refer to

4. Failure in the rotational sensor circuit...

a. Failed rotational sensor.

b. Loose connection or break between the rotational sensor and the DMC computer.

L. DMC computer will not accept any, or ONLY accept certain keyboard (touch pad) entries...

1. Failed keyboard (touch pad) label assembly.

2. Failed DMC computer.

M. DMC computer locks up and the L.E.D. display reads erroneous message(s) or ONLY partial

segments...

1. Transient power voltage (spikes)...disconnect power to the dryer, wait 1 minute (

NOTE:

for dryer models with

the optional battery back up...disconnect battery), then reestablish power to the dryer. If a problem is still
evident, proceed to

Item M2

,

Item M3

, and

Item M4

.

2. Failed keyboard (touch pad) label assembly.

3. Improper grounding of the dryer or the DMC computer ground connections to the panel or the dryer are not

proper.

4. Failed DMC computer.

N. Dryer stops during a cycle and the DMC computer L.E.D. display returns to “FILL”...

If the dryer is equipped with optional battery back up...

1. Refer to

Item M1

,

Item M3

, or

Item M4

on

this page

.

If the dryer is not equipped with optional battery back up...

1. Loose connection somewhere in the power source to the dryer.

2. Loose connection in main power circuit to the DMC computer.

3. Improper grounding of the dryer or the DMC computer ground connections to the panel or the dryer are not

proper.

4. Failed DMC computer.

«
...
50
51
52
53
54
...
»

Содержание AD-320





























































Отзывы:

Нет отзывов

Похожие инструкции для AD-320

Бренд: Aalborg Страницы: 128

Бренд: Magnescale Страницы: 3

Бренд: PACH & COMPANY Страницы: 4

Бренд: Balboa Страницы: 23

Бренд: Balboa Страницы: 2

Бренд: xpr Страницы: 4

Бренд: Parker Страницы: 54

Бренд: RAM Страницы: 71

Бренд: Fox Страницы: 5

KOOL STRIDE KS-S

Бренд: KOOL-STOP Страницы: 8

Бренд: Dakota Digital Страницы: 12

Бренд: Trane Страницы: 72

Бренд: XtendLan Страницы: 12

Бренд: ZBA Страницы: 27

Бренд: M-system Страницы: 10

Бренд: Baier Страницы: 20

Бренд: Tenpilot Страницы: 2

Бренд: Bardiani Valvole Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды