ADC AD-320 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 60

background image

112144 - 46

www.adclaundry.com

45

SECTION VIII

TROUBLESHOOTING

IMPORTANT: YOU MUST DISCONNECT AND LOCKOUT THE ELECTRIC SUPPLY AND

THE GAS SUPPLY OR THE STEAM SUPPLY BEFORE ANY COVERS OR
GUARDS ARE REMOVED FROM THE MACHINE TO ALLOW ACCESS
FOR CLEANING, ADJUSTING, INSTALLATION, OR TESTING OF ANY
EQUIPMENT PER OSHA

(Occupational Safety and Health Administration)

STANDARDS.

The information provided will help isolate the most probable component(s) associated with the difficulty described.
The experienced technician realizes, however, that a loose connection or broken/shorted wire may be at fault where
electrical components are concerned...and not necessarily the suspected component itself.

Electrical parts

should always be

checked for failure before being returned to the factory.

The information provided

should not be

misconstrued as a handbook for use by an untrained person making repairs.

IMPORTANT:

When replacing blown fuses, the replacement

must be

of the exact rating as the fuse

being replaced.

WARNING: ALL

SERVICE AND TROUBLESHOOTING

SHOULD BE

PERFORMED BY A

QUALIFIED PROFESSIONAL OR SERVICE AGENCY.

WARNING:

WHILE MAKING REPAIRS, OBSERVE

ALL

SAFETY PRECAUTIONS

DISPLAYED ON THE DRYER OR SPECIFIED IN THIS MANUAL.

A. No light emitting diode (L.E.D.) display...

1. Service panel fuse blown or tripped breaker.

2. Blown control circuit fuse (3 AG 1/2-amp [Slo-Blo] fuse).

3. Failed Dual Microprocessor Controller (DMC) computer.

B. Basket (tumbler) does not start, but motor and DMC computer motor L.E.D. dot and motor

output L.E.D. indicators are on...

1. DMC computer indicator is on...

a. Failed motor contactor/relay.

b. Failed motor.

2. DMC computer indicator is off (and the L.E.D. display does not read “door”)...

a. Failed DMC computer.

«
...
47
48
49
50
51
...
»

Содержание AD-320





























































Отзывы:

Нет отзывов

Похожие инструкции для AD-320

Бренд: Eaton Страницы: 288

Бренд: Fairchild Страницы: 2

Бренд: Fairford Страницы: 233

Бренд: Samson Страницы: 20

Бренд: Lakeshore Страницы: 186

Бренд: Panamax Страницы: 16

Бренд: Apricus Страницы: 32

Linear Technology ADI Power DC3017A

Бренд: Analog Devices Страницы: 12

Бренд: Tate Страницы: 32

WisBlock RAK19012

Бренд: RAK Страницы: 12

Бренд: Cypress Semiconductor Страницы: 36

AN-X4-ABRIO-HMI

Бренд: QTS Страницы: 48

Бренд: Polyaire Страницы: 20

Бренд: A&D Страницы: 42

Бренд: Cruisair Страницы: 30

TRILOGY T500 Series

Бренд: Eclipse Страницы: 20

MotorController WCC 310 UL

Бренд: Window Master Страницы: 39

Бренд: Allen-Bradley Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды