ADC AD-320 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 60

background image

36

American Dryer Corp.

112144 - 46

NOTE:

During the purging period, check to be sure that

ALL

gas shutoff valves are open.

Once ignition is established, a gas pressure test

should be

taken at the gas valve pressure tap of each dryer

to assure that the water column (W.C.) pressure is correct and consistent.

NOTE:

Water column pressure requirements (measured at the gas valve pressure tap):

Natural Gas ............................ 3.5 Inches (8.7 mb) Water Column.
Liquid Propane (L.P.) Gas ..... 10.5 Inches (26.1 mb) Water Column.

IMPORTANT:

There is no regulator provided in an L.P. dryer. The water column pressure

must be

regulated at the source (L.P. tank) or an external regulator

must be

added to each

dryer.

b. Electric Models

Check to insure that the heating units (electric ovens) are functioning properly.

c. Steam Models

Check to insure that the steam dampers open and close properly. If steam dampers open and/or close too
fast, make the necessary adjustments at the steam damper/piston flow control valve. Refer to the

illustration

4. Make a complete operational check of

ALL

safety related circuits (i.e., lint basket switches and sail switches).

5. Each basket (tumbler)

should be

operated through one (1) complete cycle to assure that no further adjustments

are necessary and that

ALL

components are functioning properly.

NOTE:

The sail switch (gas and electric models only) can be checked for proper operation by opening
the control door while the dryer is running and the heating unit (burner) is active (on). The
heating unit(s) should shut off within a few seconds. If not, make the necessary adjustments.

BASKET (TUMBLER) COATING

The basket (tumbler) is treated with a protective coating. We suggest dampening old garments or cloth material with
a solution of water and nonflammable mild detergent and tumbling them in the basket (tumbler) to remove this
coating.

NOTE:

Drying and cooling cycles are complete when the light emitting diode (L.E.D.) display reads
“donE.”

«
...
38
39
40
41
42
...
»

Содержание AD-320





























































Отзывы:

Нет отзывов

Похожие инструкции для AD-320

Бренд: S&C Страницы: 40

Бренд: S&C Страницы: 34

Бренд: 3M Страницы: 34

Бренд: Bang & Olufsen Страницы: 80

Бренд: Bang & Olufsen Страницы: 13

Бренд: Daikin Страницы: 38

Бренд: Daikin Страницы: 2

Бренд: Daikin Страницы: 148

Бренд: Daikin Страницы: 12

Бренд: Daktronics Страницы: 52

Бренд: Waeco Страницы: 20

Бренд: Z-Wave Страницы: 56

Бренд: Dakota Digital Страницы: 6

CMD-2000 Series

Бренд: Dakota Digital Страницы: 10

Бренд: Z-Wave Страницы: 6

Бренд: Jabra Страницы: 4

Бренд: jbc Страницы: 44

Бренд: jbc Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды