ADC AD-320 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 60

background image

12

American Dryer Corp.

112144 - 46

Even though a 12-inch (30.48 cm) clearance is acceptable, it is recommended that the rear of the dryer be positioned
approximately 2 feet (0.61 meters) away from the nearest obstruction, i.e., wall, for ease of installation, maintenance,
and service.

The dryer

must be

installed with a proper exhaust duct connection to the outside.

The dryer

must be

installed with provisions for adequate combustion and make-up air supply.

CAUTION:

This dryer produces combustible lint and

must be

exhausted to the outdoors. Every 6

months, inspect the exhaust ducting and remove any lint build up.

IMPORTANT: Dryer

must be

installed in a location/environment, which the ambient

temperature remains between 40º F (4.44º C) and 130º F (54.44º C).

C. DRYER ENCLOSURE REQUIREMENTS

Bulkheads and partitions

should be

made of noncombustible materials and

must be

located a minimum of 12-inches

(30.48 cm) above the dryer outer top, except along the front of the dryer, which may be closed in if desired.

NOTE:

Even though a minimum of 12-inches (30.48 cm) above the dryer outer top is acceptable, a
clearance of 18-inches (45.72 cm) or more is suggested for ease of installation and service
(power electrical connections).

NOTE:

When fire sprinkler systems are located above the dryers, a minimum of 12-inches (30.48 cm)
above the dryer outer top is required.

«
...
14
15
16
17
18
...
»

Содержание AD-320





























































Отзывы:

Нет отзывов

Похожие инструкции для AD-320

Бренд: Vacon Страницы: 62

Бренд: Samson Страницы: 92

Бренд: Jafar Страницы: 10

Бренд: Data I/O Страницы: 88

Бренд: Data Aire Страницы: 13

Бренд: jbc Страницы: 44

Бренд: jbc Страницы: 8

Бренд: UniPOS Страницы: 51

Бренд: Unipulse Страницы: 126

Бренд: YachtSafe Страницы: 3

Бренд: Watts Страницы: 4

Бренд: WaterCop Страницы: 4

Бренд: Jetter Страницы: 24

Бренд: Dejero Страницы: 24

Бренд: WINDY NATION Страницы: 16

Бренд: Kaba Mauer Страницы: 10

M-DUINO PLUS series

Бренд: Industrial Shields Страницы: 46

ACTIVAL VY51 5H006

Бренд: Azbil Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды