ADC AD-320 Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 60

background image

112144 - 46

www.adclaundry.com

53

e. Open main door. The dryer must stop

and

ALL

indicator lights on the back side of the microprocessor

controller (computer) board must go out.

f. Try to restart the dryer with the main door open.

g. The microprocessor controller (computer) board’s light emitting diode (L.E.D.) display must read

“DOOR.”

h. Close the main door and restart the dryer.

i. Functional check of microprocessor controller (computer) board is complete.

2. For Models With Johnson Controls Direct Spark Ignition (DSI) Module (G760)

Theory Of Operation:

Start the drying cycle. When the gas burner ignites within the chosen trial for ignition time (6-seconds), the
flame sensor detects gas burner flame and signals the DSI module to keep the gas valve open...as long as there
is a call for heat. The DSI module will “LOCKOUT” if the gas burner flame is not sensed at the end of the trial
for ignition period. The trial for ignition period will be repeated for a total of three (3) retries/trials (the initial
try and two [2] more retries/trials). If the flame is not sensed at the end of the third retry/trial (inter-purge
period of 30-seconds) the DSI module will “LOCKOUT” (L.E.D. flashes).

A steady L.E.D. indicator indicates

normal operation

.

No

L.E.D. indicator indicates a power or an internal failure has occurred.

«
...
55
56
57
58
59
...
»

Содержание AD-320





























































Отзывы:

Нет отзывов

Похожие инструкции для AD-320

Бренд: ABB Страницы: 2

Бренд: FAAC Страницы: 12

Бренд: KELCO Страницы: 36

Бренд: IBM Страницы: 144

CITY ELITE SINGLE

Бренд: Baby Jogger Страницы: 3

Бренд: BADODOSECURITY Страницы: 8

Бренд: Oldham Страницы: 32

Бренд: H3C Страницы: 14

Бренд: Rachio Страницы: 2

REVOLUTION Pro Controller 2

Бренд: Nacon Страницы: 11

Бренд: Nacon Страницы: 18

Бренд: Nacon Страницы: 24

Бренд: Nabco Страницы: 35

Бренд: S&P Страницы: 17

Бренд: S&S Northern Страницы: 9

Бренд: I-Tork Страницы: 15

Бренд: MGC Страницы: 16

Бренд: asalvo baby Страницы: 84

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды