ADC AD-320 Скачать руководство пользователя страница 38

Страница: 38 / 60

American Dryer Corp.

112144 - 46

I. PREPARATION FOR OPERATION

The following items

should be

checked before attempting to operate the dryer:

1. Read

ALL

“

CAUTION

,” “

WARNING

,” and “

DIRECTION

” labels attached to the dryer.

2. Check incoming supply voltage to be sure that it is the same as indicated on the dryer data label located on the

inside of the middle access (control) door.

GAS MODELS

- check to assure that the dryer is connected to the type of heat/gas indicated on the dryer data

label.

GAS AND ELECTRIC MODELS

- the sail switch damper assembly was installed and adjusted at the factory

prior to shipping. However, each sail switch adjustment

must be

checked to assure that this important safety

control is functioning.

5. Check bolts, nuts, screws, terminals, and fittings for tightness.

GAS MODELS

- be sure that

ALL

gas shutoff valves are in the open position.

7. Be sure

ALL

back guard panels and service box covers have been replaced.

8. Check the lint door to assure that it is closed and secured in place.

9. Rotate the basket (tumbler) by hand to be sure they move freely.

10.

STEAM MODELS

- check to insure that the air supply (80 PSI [5.51 bar]) is on the dryer.

11. For more effective automatic door closure and better tumbling action (and improved efficiency), the dryer

should be

tilted slightly to the rear.

J. PREOPERATIONAL TEST

ALL

dryers are thoroughly tested and inspected before leaving the factory. However, a preoperational test

should

performed before the dryer is publicly used. It is possible that adjustments have changed in transit. Installer must

instruct the user on how to correctly operate the dryer before leaving.

1. Turn on electric power to the dryer.

a. Open

ALL

gas or steam shutoff valves (for gas and steam models only)

2. Dual Microprocessor Controller (DMC) Computer System Operational Test

a. Coin Models Only

1) The light emitting diode (L.E.D.) display(s) will flash back and forth between “FILL” and the amount

needed to start the dryer (i.e., “25”), meaning that the dryer is available and 25¢ is required to start it.

2) Insert the proper number of coins into coin acceptor. Once the correct amount needed to start the dryer

has been inserted, the L.E.D. display(s) will read “PUSH”...“tEnP.”

Содержание AD-320





























































Результаты поиска

Содержание AD-320

Отзывы:

Похожие инструкции для AD-320

Бренды по названию

Популярные бренды

ADC AD-320, Руководство по установке

Результаты поиска

Содержание AD-320

Отзывы:

Похожие инструкции для AD-320

Бренды по названию

Популярные бренды