ADC AD-320 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 60

background image

44

American Dryer Corp.

112144 - 46

90 DAYS

Inspect and remove lint accumulation in customer furnished exhaust ductwork system and from the dryer’s internal
exhaust ducting.

WARNING: THE ACCUMULATION OF LINT IN THE EXHAUST DUCTWORK CAN

CREATE A POTENTIAL FIRE HAZARD.

WARNING:

DO NOT

OBSTRUCT THE FLOW OF COMBUSTION AND VENTILATION AIR.

WARNING: INSPECT AND REMOVE ANY LINT ACCUMULATION, WHICH CAN CAUSE

THE BACK DRAFT DAMPER TO BIND OR STICK

.

NOTE:

A back draft damper that is sticking partially closed can result in slow drying and shutdown of
the heat circuit safety switches and/or thermostats.

NOTE:

When cleaning dryer cabinet(s), avoid using harsh abrasives. A product intended for the
cleaning of appliances is recommended.

B. ADJUSTMENTS

7 DAYS AFTER INSTALLATION AND EVERY 6 MONTHS THEREAFTER

Inspect bolts, nuts, screws, (bearing setscrews), grounding connections, and nonpermanent gas connections (unions,
shutoff valves, and orifices). Motor and drive belts

should be

examined. Cracked or seriously frayed belts

should

be

replaced. Tighten loose V-belts when necessary. Complete operational check of controls and valves. Complete

operational check of

ALL

safety devices (door switches, lint drawer switch, sail switch, burner, and hi-limit

thermostats).

C. LUBRICATION

The motor bearings, idler bearings, and under normal/most conditions the basket (tumbler) bearings are permanently
lubricated. It is physically possible to relubricate the basket (tumbler) bearings if you choose to do so, even though
this practice is not necessary. Use Shell Alvania #2 grease or its equivalent. The basket (tumbler) bearings used in
the dryer

DO

NOT

have a grease fitting. Provisions are made in the bearing housing for the addition of a grease

fitting, which can be obtained elsewhere, or from

ADC

by ordering Part No. 882159...which includes two (2) grease

fittings.

«
...
46
47
48
49
50
...
»

Содержание AD-320





























































Отзывы:

Нет отзывов

Похожие инструкции для AD-320

Бренд: ABB Страницы: 30

Бренд: ABB Страницы: 15

Бренд: ABB Страницы: 10

Бренд: ABB Страницы: 44

Бренд: Watts Страницы: 2

Бренд: Febco Страницы: 4

Бренд: Cisco Страницы: 48

Бренд: T-Verter Страницы: 121

Бренд: Happy Страницы: 10

Бренд: ICM Controls Страницы: 2

Бренд: NAiS Страницы: 144

ArtNet-DMX Mux16

Бренд: DMX4ALL Страницы: 21

Бренд: Dejero Страницы: 24

Бренд: WINDY NATION Страницы: 16

Бренд: Kaba Mauer Страницы: 10

Бренд: Nordelettronica Страницы: 8

Бренд: Gemini Страницы: 9

Бренд: M-system Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды