ADC AD-320 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 60

background image

112144 - 46

www.adclaundry.com

11

SECTION III

INSTALLATION PROCEDURES

Installation

should be

performed by competent technicians in accordance with local and state codes. In the absence

of these codes, the installation

must conform

to applicable American National Standards: ANSI Z223.1-LATEST

EDITION (National Fuel Gas Code) or ANSI/NFPA NO. 70-LATEST EDITION (National Electrical Code) or in
Canada, the installation

must conform

to applicable Canadian Standards: CAN/CGA-B149.1-M91 (Natural Gas)

or CAN/CGA-B149.2-M91 (Liquid Propane [L.P.] Gas) or LATEST EDITION (for General Installation and Gas
Plumbing) or Canadian Electrical Codes Parts 1 & 2 CSA C22.1-1990 or LATEST EDITION (for Electrical
Connections).

A. UNPACKING/SETTING UP

Remove protective shipping material (i.e., plastic wrap and/or optional shipping box) from dryer.

NOTE:

The access keys for the service doors are included in the information packet shipped in the
basket (tumbler). These keys

should be

removed and put in a safe place yet made accessible

because some

will

be

needed throughout various phases in the installation of the dryer.

Dryers are shipped with a coin box and coin box faceplate ONLY.

The coin box lock is not included and

must

be

purchased elsewhere or the lock can be ordered as a parts order from the

ADC

factory.

The dryer can be moved to its final location while still attached to the skid or with the skid removed. To unskid the
dryer, locate and remove the four (4) bolts securing the base of the dryer to the wooden skid. Two (2) are at the rear
of the base, and two (2) are located in the front. Once the bolts are removed, slide the dryer off the skid.

With the skid removed, to make it easier to slide the dryer into its final position, slightly lower

ALL

four (4) leveling

legs, so that the dryer will slide on the legs instead of the base frame. The dryer is equipped with four (4) leveling
legs, one (1) at each corner of the dryer base. The hex head adjustment bolts for the two (2) front leveling legs are
located directly behind the lower access door, and the rear two (2) adjustments are directly behind the lower rear
back (guard) panel.

For more effective automatic door closure and better tumbling action (and improved efficiency), the dryer

should be

tilted slightly to the rear.

B. LOCATION OF THE DRYER

Before installing the dryer, be sure the location conforms to local codes and ordinances. In the absence of such
codes or ordinances the location

must conform

with the National Fuel Gas Code ANSI.Z223.1 LATEST EDITION,

or in Canada, the installation

must conform

to applicable Canadian Standards: CAN/CGA-B149.1-M91 (Natural

Gas) or CAN/CGA-B149.2-M91 (L.P. Gas) or LATEST EDITION (for General Installation and Gas Plumbing).

The dryer

must be

installed on a sound level floor capable of supporting its weight. Carpeting

must be

removed

from the floor area that the dryer is to rest on.

IMPORTANT:

“The dryer

must be

installed on noncombustible floors only.”

«
...
13
14
15
16
17
...
»

Содержание AD-320





























































Отзывы:

Нет отзывов

Похожие инструкции для AD-320

Бренд: XBOX Страницы: 4

Бренд: ICP DAS USA Страницы: 166

Бренд: ICP DAS USA Страницы: 64

Tunnel Master Jr

Бренд: ICS Страницы: 83

PROFIBUS PROFI-2510

Бренд: ICP DAS USA Страницы: 4

Бренд: ICP DAS USA Страницы: 40

Бренд: Raypak Страницы: 24

Бренд: J+J Страницы: 91

Бренд: Yamaha Страницы: 92

Бренд: WAGNER Страницы: 60

Бренд: W.E.ST. Страницы: 34

Бренд: Ltech Страницы: 4

Бренд: Motor Guard Страницы: 2

Бренд: K&K Страницы: 6

Бренд: Frico Страницы: 8

Serial Interface Module

Бренд: Federal Signal Corporation Страницы: 12

Бренд: Bardiani Страницы: 22

Бренд: Zander Aachen Страницы: 75

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды